English - AEG BPS18-254BL Manual Original

Before work, make a dummy cut without the motor turned on so
the position of the blade, operation of the guards with respect to
other machine parts, and workpiece may be checked.
Refrain from removing any cut-o s or other parts of the workpi-
ece from the cutting area whilst the machine is running and the
saw head is not in the rest position.
When transporting the machine, use only transportation devices
and never use guards for handling or transportation.
The handle lock must always be engaged when transporting the
mitre saw.
Keep the oor area free of loose material e.g. chips and cut-o s.
Long workpieces must be adequately supported.
Stock having a round or irregular cross section (such as rewood)
must not be cut, as it can not be securely held during cutting.
When sawing thin stock layed on edge, a suitable auxilary fence
must be used for rm support.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Use a dust absorption system and
wear a suitable dust protection mask. Remove deposited dust
thoroughly, e.g. with a vacuum cleaner.
Connect the saw to a dust-collecting device when sawing wood.
Do not replace the LED or laser with a di erent type. Any repairs
must only be carried out by the manufacturer or authorised
service agent.
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Transport and store the tools in a suitable receptacle;
Any faults with the machine, including any related to the safegu-
ard or the saw blades, must be reported to the persons in charge
of safety as soon as the faults are discovered.
When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance from the blade.
Adapt the feed speed to avoid overheating the blade tips and to
avoid melting plastic materials during cutting.
WARNING Do not replace the LED with a di erent type.
WARNINGTo reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in uid or allow a uid to ow inside them.
Corrosive or conductive uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
WOOD CUTTING BLADE SAFETY WARNINGS
Please read the manual and instructions carefully before using the
saw blade and the machine.
The machine must be in good condition, the spindle without
deformation and vibration.
Do not use the saw without the guards in position, keep guards in
good working order and properly maintained.
Ensure the operator is adequately trained in safety precautions,
adjustment, and operation of the machine.
Always wear goggles and ear protection when using the machine.
It is recommended to wear gloves, sturdy non-slip shoes and
apron.
Before using any accessory, consult the instruction manual. The
improper use of an accessory can cause damage and increase the
potential for injury.
Use only blades speci ed in this manual, complying with EN 847-1.
Observe the maximum speed marked on the saw blade. Ensure
the speed marked on the saw blade is at least equal to the speed
marked on the saw.
Always use blades with correct size and shape of arbour holes.
Blades that do not match the mounting hardware of the saw will
run eccentrically, causing loss of control.
Do not use blades of larger or smaller diameter other than
recommended. Do not use any spacers to make the blade t onto
the spindle.
Check the tips of the saw blade for damage or abnormal appea-
rance before each use. Tips that are damaged or loose can become
ying objects in use and increase the chance of personal injury.
Do not use cracked or distorted saw blades. Do not use saw blades
which are damaged or deformed
Scrap the saw blade if damaged, deformed, distorted or cracked,
repairing is not permitted.
Do not use HSS blades.
Ensure the saw blade is mounted correctly, tighten the arbor nut
securely before use (tightening torque approx. 12 Nm).
Fastening screw and nuts shall be tightened using the appropriate
spanner, etc.
Extension of the spanner or tightening using hammer blows is not
permitted.
Make sure the blade and anges are clean and the recessed sides
of the collar are against the blade.
Make sure the blade rotates in the correct direction.
Before work, make a dummy cut without the motor turned on so
the position of the blade, operation of the guards with respect to
other machine parts and workpiece may be checked.
Never leave the machine unattended.
Do not apply lubricants on the blade when it is running.
Never perform any cleaning or maintenance work when the
machine is still running and the head is not in the rest position.
Never attempt to stop a machine in motion rapidly by jamming
a tool or other means against the blade, serious accidents can be
caused unintentionally in this way.
Disconnect the saw from the mains supply or remove battery pack
before changing blades or carrying out maintenance.
Pay attention to blade packing and unpacking, it is easy to be
injured by the sharp blade tips.
Use a blade holder or wear gloves when handling a saw blade.
Keep and store the blade in original packaging or other suitable
packaging, keep in dry conditions and away from chemicals which
may damage the blade.
SAFETY WARNINGS LASER
The laser radiation used in this saw is Class 1 with maximum
<1mW and 650nm wavelengths. Do not view directly with optical
instruments. Failure to comply with the rules could result in serious
personal injury.
Do not stare into beam during operation.
Do not project the laser beam directly into the eyes of others.
Serious eye injury could result.
Do not place the laser in a position that may cause anyone to stare
into the laser beam intentionally or unintentionally.
Do not use optical tools to view the laser beam.
Do not operate the laser around children or allow children to operate
the laser.
GB

English

31