Cleaning And Disinfection; Storage And Transportation - 3M 6000 Serie Manual Del Usuario

clockwise. Replace nose cup assembly.(Fig 7 )
Centre Adaptor Gasket (6896) Replacement. The closed
cell foam rubber centre adaptor gasket is designed to seal the
interface between the centre adaptor and the lens. Remove
nose cup assembly, and centre adaptor from lens centre port
as described above. Remove old gasket from centre adaptor
and replace with new replacement gasket. Re-install centre
adaptor into facepiece lens. Replace nose cup assembly.
(Figs 5-7)
Exhalation Valve (7583) Replacement. Remove exhalation
valve cover by pulling out from bottom latch. Grasp valve and
pull each valve stem out from valve seat. Place exhalation
valve replacement over the exhalation port by inserting stems
and pulling through from the opposite side until they are both
snapped in place. Replace valve cover by aligning top opening
in the valve cover with the top tab on the centre adapter base
and snap to the centre adapter base. Figure 8.
Inhalation Gaskets (6895) Replacement. The inhalation
gaskets are designed to seal the interface between inhalation
ports and filters / air supply unit. The gaskets should be
inspected with each filter change and replaced whenever
damaged or seal integrity is questionable. Remove gaskets
from inhalation port bayonet fittings. Install new gaskets onto
inhalation port under all three bayonet lugs. Figure 9.
Inhalation Valves (6893) Replacement. Inhalation valves are
located on posts at the inside of the facepiece inhalation ports
and inside the nose cup inhalation ports. These valves should
be inspected before each respirator use and replaced
whenever valves become damaged or lost. Remove existing
inhalation valve(s) by lifting from post(s) at the inside of the
facepiece and nose cup inhalation port(s). Install new valve(s)
onto post(s). Be certain valve is fully engaged under all three
lugs on post, lies flat, and spins freely on post.
Head Harness (6897) Replacement. Unbuckle head harness
straps and replace with new head harness. Figure 10.
Lens Assembly (6898) Replacement. Remove the two sets
of screws using a screwdriver. Then, pull the frame top and
frame bottom away from the faceseal. The frame top, frame
bottom, faceseal and the lens assembly have vertical line
markings that indicate their positions relative to one another.
Make certain these markings are aligned for re-assembly.
Figure 11.
Neck Strap (7883). Connect loops at end of neck strap
assembly onto the face seal tabs at the top of the head
harness.
ACCESSORIES
Spectacle Kit (6878). Install rail assembly into Facepiece with
the plastic foot positioned on centre port adapter and the top
of rail centred between the lugs or projections at top of face
seal. Install frame assembly onto rail assembly by inserting
pins into holes in rubber slide. Spectacles can now be
adjusted for optimal fit and vision.
Lens Covers (6885). Remove release liner from adhesive at
each side of replacement lens cover. Position lens cover over
the facepiece lens and adhere in place. Remove used lens
cover by lifting tab away from facepiece.

CLEANING AND DISINFECTION

Cleaning is recommended after each use. If the respirator is to
be used for more than one shift it should be cleaned at the end
of each shift and stored in the original packaging or a sealed
container. Use the 3M™ 105 Face Seal Cleaner to clean the
respirator. Remove the filters and disconnect the air supply
unit if appropriate. Clean parts (excluding filters) by immersing
in warm cleaning solution (water temperature not to exceed
50°C), scrub with soft brush until clean. Add neutral detergent
if necessary. Disinfect respirator by soaking in a solution of
quaternary ammonia disinfectant or sodium hypochlorite or
other disinfectant. Rinse in clean, warm water and air dry at
room temperature in a non-contaminated atmosphere.
CAUTION Do not use cleaners containing lanolin or other oils
on these products. Do not autoclave. Do not use petrol,
chlorinated degreasing fluids (such as trichloroethylene),
organic solvents or abrasive cleaning agents to clean any part
of the equipment. Do not reassemble parts until facepiece is
completely dry.

STORAGE AND TRANSPORTATION

These products should be stored in the packaging provided in
dry, clean conditions away from direct sunlight, sources of
high temperature, petrol and solvent vapours. The original
packaging is suitable for transporting the product throughout
the European Union. When stored as stated, the expected
shelf life of the product is 5 years from date of manufacture.
Store in accordance with manufacturer's instructions, see
packaging.
] End of Shelf Life
\ Temperature Range
, Maximum Relative Humidity
: Name and address of Manufacturer
J Dispose of in accordance with local regulations
The date of manufacture can be established by examining the
date clock on the inside of the facepiece. Figure 12. The inner
segment will display the year, and the arrow will point to the
month of manufacture in the outer segment. The example
shows 01/09/2011 - 30/09/2011.
APPROVALS
These products meet the requirements of the European
Community Directive 89/686/EEC (Personal Protective
Equipment Directive) and are thus CE marked.
Certification under Article 10, EC Type-Examination and
Article 11, EC Quality Control, has been issued by BSI,
Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes, MK5
8PP, UK (Notified body number 0086).
6