Stanley J7C09D Manual De Instruccion página 4

• Vehicles that have on-board computerized systems may be damaged if vehicle
battery is jump-started. Before jump-starting, read the vehicle's owner's manual to
confirm that external-starting assistance is suitable.
• Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or
power station
• Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to
persons.
• Be extra careful to avoid dropping a metal tool onto the battery. It might spark or
short-circuit the battery or another electrical part and could cause an explosion.
• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.
• Always store battery clamps when not in use. Never touch battery clamps together.
This can cause dangerous sparks, power arcing and/or explosion.
• When using this unit close to the vehicle's battery and engine, stand the unit on a
flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts
away from moving vehicle parts.
• Never allow red and black clamps to touch each other or another common
metal conductor – this could cause damage to the unit and/or create a sparking/
explosion hazard.
– For negative-grounded systems, connect the positive (red) clamp to the positive
ungrounded battery post and the negative (black) clamp to the vehicle chassis
or engine block away from the battery. Do not connect the clamp to the
carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge
metal part of the frame or engine block.
– For positive-grounded systems, connect the negative (black) clamp to the
negative ungrounded battery post and the positive (red) clamp to the vehicle
chassis or engine block away from the battery. Do not connect the clamp to
the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge
metal part of the frame or engine block.
• If the clamps are connected incorrectly with regard to polarity, the backlit LCD
screen will display the Battery Status Icon, Battery Voltage Indicator, and the Clamp
Icons. The Alarm Icon, the "+" and "–" signs and the Reverse Polarity Icons will
flash and the unit will sound a continuous alarm until the clamps are disconnected.
Disconnect the clamps and reconnect to battery with correct polarity.
• Always disconnect the negative (black) jumper cable first, followed by the positive
(red) jumper cable, except for positive grounded systems.
• Do not expose battery to fire or intense heat since it may explode. Before
disposing of the battery, protect exposed terminals with heavy-duty electrical tape
to prevent shorting (shorting can result in injury or fire).
• Place this unit as far away from the battery as cables permit.
• Never allow battery acid to come in contact with this unit.
• Do not operate this unit in a closed area or restrict ventilation in any way.
• This system is designed to be used only on vehicles with a 12 volt DC battery
system. Do not connect to a 6 volt or 24 volt battery system.
• This system is not designed to be used as a replacement for a vehicular battery. Do
not attempt to operate a vehicle that does not have a battery installed.
• Excessive engine cranking can damage a vehicle's starter motor. If the engine
fails to start after the recommended number of attempts, discontinue jump-start
procedures and look for other problems that may need to be corrected.
• Do not use this Jump-Starter on a watercraft. It is not qualified for marine
applications.
• Although this unit contains a non-spillable battery, it is recommended that unit be
kept upright during storage, use and recharging. To avoid possible damage that
may shorten the unit's working life, protect it from direct sunlight, direct heat and/
or moisture.
SPECIFIC SAFETY INSTRUCTIONS FOR THE USB PORTS
• Do not insert foreign objects into the USB Ports.
• Do not attach USB hubs or more than one personal electronic device to each USB
Port.
• Do not use this unit to operate appliances that require more than 3.1A (5V) to
operate from each of the USB Ports.
• Some household USB-powered electronics will not operate with this unit.
SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS
CAUTION –
To reduce the risk of injury or property damage:
• Never leave the compressor unattended while in use.
• Do not operate compressor continuously for longer than approximately 10
minutes, depending on ambient temperatures, as it may overheat. This could
damage the compressor. Follow the instructions in the "Portable Compressor"
section.
WARNING –
Burst hazard: Bursting articles can cause serious injury.
• Carefully follow instructions on articles to be inflated.
• Never exceed the recommended pressure listed in instructions on articles to be
inflated. If no pressure is given, contact article manufacturer before inflating.
J7C09D_ManualENSP_060921.indd 6-7 J7C09D_ManualENSP_060921.indd 6-7
• Monitor the pressure at all times on the LCD screen.
PERSONAL SAFETY
When working with lead acid batteries, always make sure immediate assistance is
available in case of accident or emergency.
Remove personal metal items such as rings, bracelets, necklaces and watches when
working with a lead acid battery. A lead acid battery can produce a short circuit
current high enough to weld a ring, or similar metal object, to skin, causing a
severe burn.
Do not wear vinyl clothing when jump-starting a vehicle. Friction can cause
dangerous static-electrical sparks.
Always have protective eyewear when using this product: contact with battery acid
may cause blindness and/or severe burns. Be aware of first aid procedures in case of
accidental contact with battery acid.
Have plenty of fresh water and soap nearby in case battery acid contacts skin.
SKIN:
• If battery acid comes in contact with skin, rinse immediately with water,
then wash thoroughly with soap and water. If redness, pain, or irritation occurs,
seek immediate medical attention.
EYES:
• If battery acid comes in contact with eyes, flush eyes immediately, for a
minimum of 15 minutes and seek immediate medical attention.
LCD LIQUID CRYSTAL DISPLAY:
• If liquid crystal comes in contact with
your skin: Wash area off completely with plenty of water. Remove contaminated
clothing. If liquid crystal gets into your eye: Flush the affected eye with clean
water and then seek medical attention. If liquid crystal is swallowed: Flush
your mouth thoroughly with water. Drink large quantities of water and induce
vomiting. Then seek medical attention.
SAVE THESE
INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Portable Power Station. Read this
Instruction Manual and follow the instructions carefully before using this
unit.
OVERVIEW
Common Actions and Unit Responses
The following actions turn the unit on and activate the LCD screen:
Press the LED Area A beep will sound and the Area Light will turn on.
Light Power Button.
The backlight will turn on for 10 seconds (only).
(Refer to the "LED Area The LCD screen will continue to display the Battery
Light" section.) Status Icon and Battery Voltage Indicator. The unit
remains on until the LED Area Light Power Button
is pressed again to turn it off.
Press the USB Power A beep will sound and the USB Ports will turn on.
Button. (Refer to the The backlight will turn on for 10 seconds (only).
"USB Ports" section.) The LCD screen will display the Battery Status
Icon, Battery Voltage Indicator, and the USB Icon;
indicating the three USB Ports are active. The unit
remains on until the USB Power Button is pressed
again to turn it off.
Press the Compressor A beep will sound and the backlit LCD screen will
Power Button. (Refer
display the Battery Status Icon, "XXX" PSI and the
to the "Portable Compressor Icon. If no further actions are taken
Compressor" section.) after 1 minute, the unit will display the Battery
Status Icon and Battery Voltage Indicator for 10
seconds before automatically turning off.
6
If the Jump-Starter ... a two-second warning will sound every 10
Switch has been seconds. The backlit LCD screen will display the
turned to the on Battery Status Icon, Battery Voltage Indicator, the
position and the
Clamp Icons, and the "+" and "–" signs. The Alarm
clamps are not Icon and the Jump-Starter Icon will flash. The unit
connected to a battery remains on until the Jump-Starter Power Switch is
(refer to the "Jump- switched off and then displays the battery status
Starting Your Vehicle" icon and the voltage of digital display for 10
section) ... seconds before automatic shut down.
If the clamp ... the backlit LCD screen will display the Battery
connections to the
Status Icon, Battery Voltage Indicator, and the
battery's positive and Clamp Icons. The Alarm Icon, the "+" and "–"
negative terminals signs and the Reverse Polarity Icons will flash and
are reversed (refer the unit will sound a warning continuously until
to the "Jump-Starter" the clamps are disconnected from the battery.
section) ...
Whenever the
... a beep will sound and the backlit LCD screen
clamps are properly will display the Battery Status Icon, Battery Voltage
connected to a battery Indicator, the Clamp Icons, and the "+" and "–"
(refer to the "Jump- signs. The Jump-Starter Icon will flash. The unit
Starting Your Vehicle" remains on until the clamps are
section) ...
disconnected from the battery.
When the unit is ... the backlight will turn on for 10 seconds (only).
charging or recharging
The LCD screen will continue to display the Battery
using the built-in Status Icon and Battery Voltage Indicator. The bars
120 Volt AC Charger on the Battery Status Icon will change from empty
(refer to the "Charging/ to solid (bottom to top) repeatedly.
Recharging" section) ...
Note:
The unit will automatically power off once ALL the functions are turned off.
VIEWING BATTERY STATUS
The Battery Status Icon and Battery Voltage Indicator indicate the battery charge
level as follows.
• If the battery charge level is at full capacity, four solid bars will display.
• If the battery is partially charged, two or three solid bars will display.
• If the battery is nearly empty, one solid bar will display. The unit should be
charged at this time.
• If the battery is completely empty, four blank bars will display. The unit MUST be
charged at this time or the unit's built-in low voltage protection will activate. The
empty Battery Status Icon will flash for a short period of time before automatic
shut down. The unit will not operate until the battery is recharged.
CHARGING/RECHARGING
This unit is delivered in a partially charged state – you must fully charge it before
using it for the first time. Initial AC charge should be for 40 hours or until the Battery
Status Icon shows 4 solid bars.
Lead-acid batteries require routine maintenance to ensure a full charge and long
battery life. All batteries lose energy from self-discharge over time and more
rapidly at higher temperatures. Therefore, batteries need periodic charging to
replace energy lost through self-discharge. When the unit is not in frequent use,
manufacturer recommends the battery should be recharged at least every 30 days
and after each use.
Failure to keep the battery charged will cause permanent damage and result in
poor Jump-Starting performance.
IMPORTANT NOTES:
• Recharging the battery after each use will prolong battery life; frequent heavy
discharges between recharges and/or overcharging will reduce battery life.
• Make sure all other unit functions are turned off during recharging, as this can
slow the recharging process.
• If you know the unit is discharged, but the battery icon displays four solid bars as
if the unit is fully charged when connected to a charging power source, this may
be due to the internal battery having high impedance. The manufacturer suggests
leaving the unit charging for a period of 40 hours using the built-in AC charger
before use.
Charging/Recharging Using the Built-In 120 Volt AC
Charger and AC Extension Cord (not included)
1. Lift the protective cover of the built-in 120 Volt AC Charger (refer to the
"Features section to locate). Connect an extension cord to the unit. Plug the
other end of the cord into a standard 120-volt AC wall outlet. When the unit
is properly connected to an AC power source, the LCD screen will display the
following:
The bars on the Battery Status Icon represent the charge level of the unit's
internal battery. The bars on the Battery Status Icon will change from empty to
solid (bottom to top) repeatedly to indicate the unit is charging. The backlight
will turn on for 10 seconds (only).
2. Charge for approximately 40 hours or until the Battery Status Icon shows 4
solid bars.
3. When charging is complete, unplug the AC extension cord from the AC outlet
and then disconnect it from the unit.
12 VOLT DC CHARGING METHOD
Charging the unit from an external 12 volt DC power source requires the use of the
optional 12 Volt DC adapter (not included).
1. Lift the protective cover of the Built-in 120 V AC Charger located on the back
of the unit. Make sure the AC extension cord is disconnected from the 120 V
AC Charger.
2. Insert the barrel tip of the 12 V DC Charging Adaptor into the 12 V DC
Charging Port on the back of the unit.
3. Insert the grooved tip of the 12 V DC Charging Adaptor into the vehicle's 12
V DC accessory outlet or other functioning 12 V DC power source. The 12V
DC Charging Adapter LED Indicator will light to indicate the unit is properly
plugged into the 12V DC power source and is in charging.
4. Charge the unit until the Battery Status Icon shows 4 solid bars when either
the Area Light, USB or Compressor Power Button is pressed (with the adapter
unplugged from the unit).
5. When charging is complete, remove the DC Charging Adaptor from the unit
and the 12 V DC power source when not in use and store in a safe place.
Notes:
Some vehicles require that the ignition be switched to the accessory outlet position in order to power
the accessory outlet. Do not leave the unit unattended when charging using the this method.
JUMP-STARTER
This Jump-Starter is equipped with an On/Off Power Switch. Once the connections
are properly made, turn the switch on to jump-start the vehicle.
IMPORTANT: Make sure the Compressor Power Button has been turned off before
attempting to use the unit as a Jump-Starter.
1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell
phone chargers, etc.). Place vehicle in "park" and set the emergency brake.
2. Make sure the Jump-Starter Power Switch is turned to off.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the
black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative
battery terminal is connected to chassis) (MOST COMMON)
4a. Connect positive (+) red clamp to vehicle battery's positive terminal.
4b. Connect negative (–) black clamp to chassis or a solid, non-moving, metal
vehicle component or body part. Never clamp directly to negative battery
terminal or moving part. Refer to the automobile owner's manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
Notes:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery
terminal is connected to chassis), replace steps 4a and 4b above with steps 5a and 5b, then
proceed to step 6.
5a. Connect negative (–) black clamp to vehicle battery's negative terminal.
5b. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving,
metal vehicle component or body part. Never clamp directly to positive
battery terminal or moving part. Refer to the automobile owner's
manual.
6. When clamps are connected properly, turn the Jump-Starter Power Switch to
ON. The backlit LCD screen will display the following:
7
6/9/2021 1:56:29 PM 6/9/2021 1:56:29 PM