Tabla de contenido
Idiomas disponibles
Idiomas disponibles
NOTE: Working with a partner as needed, lift
the TorqueMaster
spring tube assembly up
®
and rest it on top of the flag angles.
Center
Left hand
Flag
bracket
cable
angle
drum
assembly
Label
NOTE: Cable drum assemblies are marked right and left hand. Cable drums and TorqueMas-
ter
spring tube assembly are cam shaped to fit together only one way.
®
Starting on the right hand side, pre-wrap the cable drum with the counterbalance lift cable
1/2 wrap, as shown. Position the TorqueMaster
is pointing straight up. Slide the cable drum over the winding shaft until the cable drum
seats against the TorqueMaster
spring tube assembly. The winding shaft must extend past
®
the cable drum far enough to expose the splines and the grooves. Align the winding shaft
grooves with the round notch in the flag angle.
Cam peak
Counterbalance
Winding
lift cable 1/2
straight up
shaft
wrap
5"
Right
TorqueMaster
®
hand
spring tube
cable
assembly
drum
Counterbalance
lift cable
FOR DOUBLE SPRING APPLICATIONS: Repeat for left hand side.
Winding
Counterbalance lift
shaft
cable 1/2 wrap
5"
TorqueMaster
spring tube
Left hand
assembly
cable drum
Counterbalance
lift cable
FOR SINGLE SPRING APPLICATIONS: Insert the idler bracket into the left hand cable drum.
Lightly press the idler bracket into the cable drum until two distinct clicks are heard, or the
bracket is inserted all the way.
IMPORTANT: ENSURE THE SNAPS ON THE IDLER BRACKET (LEFT HAND SIDE) ARE EN-
GAGED INTO THE LEFT HAND CABLE DRUM, SO THAT IT DOES NOT COME BACK OUT.
NOTE: The idler bracket is designed for permanent assembly. Do not attempt to remove idler
bracket once inserted into the cable drum.
NOTE: The idler bracket must extend past the cable drum far enough to expose the groove.
Align the idler bracket groove with the round notch in the flag angle.
Flag angle
Right hand cable
drum assembly
®
spring tube assembly so the cam peak
Right hand
cable drum
Bearing
Groove
Cam
peak
Winding
straight
shaft
up
Round notch
in flag angle
Insert winding
Splines
shaft into flag
angle
Left hand
cable drum
Bearing
Groove
Cam
peak
Winding
straight
shaft
®
Round notch
in flag angle
Splines
Insert winding
shaft into flag
angle
Counterbalance lift
cable 1/2 pre-wrap
Round
notch
Snaps
Groove
Idler
bracket
Flag
angle
Idler
Snaps
bracket
Groove
15
Attaching End Brackets To Flag Angles
IMPORTANT: WARNING TAGS MUST BE SECURELY ATTACHED TO END BRACKET(S).
IMPORTANT: FOR SINGLE SPRING DOORS, ENSURE THE LEFT HAND CABLE DRUM BEARING
IS ALL THE WAY TO THE LEFT AND UP AGAINST THE FLAG ANGLE. IF THE CABLE DRUM IS
PULLED AWAY FROM THE FLAG ANGLE, THEN THE IDLER BRACKET CAN RUB AGAINST THE
CABLE DRUM CAUSING NOISE.
NOTE: Drill 3/16" pilot holes into header for the lag screws.
Beginning with the right hand side, slide the end bracket onto the winding shaft so that the
splines in the ratchet wheel fit onto the winding shaft grooves. Attach the end bracket to the
flag angle using (1) 5/16" - 18 x 3/4" carriage bolt, (1) 5/16" washer and (1) 5/16" - 18 hex
nut. Then secure the end bracket to the jamb using (1) 5/16" x 1-5/8" lag screw.
NOTE: If ratchet wheel falls out of end bracket, refer to illustration for proper insertion
orientation.
FOR DOUBLE SPRING APPLICATIONS: Repeat same process for left hand end bracket.
Right hand
cable drum
TorqueMaster
®
spring tube
assembly
up
Right hand
cable drum
hand end
bracket
TorqueMaster
®
spring tube
assembly
Winding
shaft
Flag
angle
FOR SINGLE SPRING APPLICATIONS: Secure the idler bracket to the flag angle using (1)
5/16" - 18 x 3/4" carriage bolt, (1) 5/16" washer and (1) 5/16" - 18 hex nut. Then secure
the idler bracket to the jamb using (1) 5/16" x 1-5/8" lag screw.
8
Cam peak
straight up
Left hand
cable drum
Idler
bracket
Bearing
Flag
angle
Left hand
cable drum
Idler
bracket
Groove
Disconnect cable
guide hole
Grooves
Right
hand
Winding
end
shaft
bracket
Splines
Warning
Flag
tag
angle
Right
5/16" -18 x 3/4"
Carriage bolt
Flag
APPLICATIONS: Repeat
angle
TorqueMaster
®
spring tube
assembly
Counterbalance
lift cable
Left
hand
cable
Snaps
drum
Ratchet wheel
(oriented correctly)
5/16" x 1-5/8"
Lag screw
5/16"
Washer
5/16"
Hex nut
FOR DOUBLE SPRING
same process for left
hand end bracket.
Capítulos
Tabla de contenido
