Level Control - Behringer MINIFBQ FBQ800 Manual Del Usuario

10 MINIFBQ FBQ800
MINIFBQ FBQ800 Controls
Controls
(EN)
(4) (2)
(3) (5) (6)
FBQ800 front panel
(1)
(POWER) button: To turn the FBQ800 on and off , use
this button, pushed in and illuminated: The FBQ800 is on.
Not pushed in and not illuminated: The FBQ800 is off .
(2)
IN/OUT button: To activate or, alternatively deactivate
control elements, use this button, pushed in and
illuminated: The FBQ800 activates all control elements.
Not pushed in and not illuminated: The FBQ800 deactivates
most control elements. However, you can use the METER
(5) (6)
SELECT button and the IN/OUT meter .
(3)
LEVEL CONTROL: To adjust the level of the input signal,
turn this control toward -12 dB (minimum setting) or,
alternatively +12 dB (maximum setting).
(4)
LOW CUT button: To manage the low-cut fi lter, use this
button, pushed in and illuminated: The low-cut fi lter
eliminates sounds that are below 75 Hz (fl oor rumble, room
resonance, and mains hum, for example). Not pushed in
and not illuminated: The low-cut fi lter does not eliminate
any sounds.
(5)
METER SELECT button: To select the type of signal you
want to monitor, use this button, pushed in and illuminated:
Monitor the input signal as soon as this signal enters the
FBQ800. The FBQ800 does not apply the LEVEL control or any
other control elements to the input signal that you monitor.
Not pushed in and not illuminated: Monitor the output
signal as soon as this signal leaves the FBQ800. The FBQ800
applies all control elements to the output signal that you
monitor. However, if you deactivated most of the control
(2)
elements , the input signal and the output signal are
the same.
(8)
(9) (7) (1)
(6)
IN/OUT METER: To monitor the level of the signal that you
selected with the METER SELECT button, use this stereo
meter. Both the left (L) and right (R) sides of this meter
share the same decibel scale (-24 dB to +6 dB). If the signal
level is too high, the CLIP LED illuminates.
(7) RANGE button: To select a range for the EQ faders, use this
button, pushed in and illuminated: The fader range extends
from -6 dB to +6 dB. Not pushed in and not illuminated:
The fader range extends from -12 dB to +12 dB.
(8)
FBQ IN button: To manage the FBQ Feedback Detection
System, use this button, pushed in and illuminated: The
FBQ Feedback Detection System is activated. If the signal
level is high in a frequency band, the relevant fader LED
illuminates brightly. In addition, all other fader LEDs are
dimmed. To reduce the potential for feedback, cut the signal
(9)
in the relevant frequency band . Not pushed in and not
illuminated: The FBQ Feedback Detection System is not
activated. Fader LEDs illuminate with identical brightness.
They do not identify possible feedback frequencies.
(9) (2)
EQ SECTION: If you activated all control elements ,
the input signal travels to the EQ section.
11 Quick Start Guide
(10) (13) (14) (11) (12)
FBQ800 rear panel
(10)
POWER connector.
(11)
RCA INPUT, L (left) and R (right): for RCA plugs
(12)
¼" TRS INPUT, L (left) and R (right): for TRS (balanced)
or, alternatively TS (unbalanced) plugs.
(13) ¼" TS OUTPUT, L (left) and R (right): for TS
(unbalanced) plugs
(14)
RCA OUTPUT, L (left) and R (right): for RCA plugs.