GGP ITALY SPA MC48Li Manual De Instrucciones página 71

■ Follow the steps the section "ADJUSTING THE
CHAIN TENSION" earlier in this manual. Kontrollera
att du har det svärd och kedja som rekommenderas i
specifikationsavsnittet tidigare i denna manual.
ADDiNg CHAiN & BAR LUBRiCANT
■ Unscrew and remove the cap (item 6) from the oil tank.
■ Pour the oil into the oil tank and monitor the oil level
gauge (item 7). Ensure that no dirt enters the oil tank
while filling the oil in.
■ Put the oil cap back on and tighten it up.
■ One full oil tank will enable you to use the saw for 20- 40
min.
TRANSPORTiNg THE CHAiN SAW
Before transporting the chain saw, always remove the battery
pack from the chain saw and slide the chain cover over the
bar and chain. If several cuts are to be performed with the
chain saw, the saw must be switch off between cuts.
gUiDE BAR COVER see figure 1
The chain cover must be clipped onto the chain and bar as
soon as the sawing work has been completed and whenever
the machine has to be transported.
SHARPENiNg THE SAW CHAiN
See figure 16 - 21
When the chain penetrates into wood with difficulty, it needs
sharpening as follows:
■ Put the chain under tension.
■ Fasten the bar in a vice so that the chain can slide.
■ Fasten the file to the file holder and place it on cutter at
35° angle.
■ File with forward strokes only until all the worn out parts of
the cutting edge are taken away.
■ Count the number of strokes given to the cutter as a
reference and file away with the same number of strokes on
all other cutters.
■ If the depth gauge protrudes from the template after
sharpening a few times, reset its level. Use a flat file. Finally,
round off the depth gauge.
NOTE: It is recommended to have the deep or important
sharpening carried out by a service agent who is equipped
with electric sharpener.
gUiDE BAR MAiNTENANCE
■ When you have finished working, clean out the groove and
the oil passages with a scraping hook.
■ Periodically trim the sides of rails using a flat file. If not
done in the long run, the feather edges might break away and
damage the bar.
■ If one rail is higher than the other one, it is necessary to
make it even with a flat file then smooth it with a file or fine
grain abrasive paper.
When servicing, use only identical replacement parts. Use
of any other parts may create a hazard or cause product
damage.
WARNiNg
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing any
maintenance.
gENERAL MAiNTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps, etc.
Tighten securely all fasteners and caps and do not operate
this product until all missing or damaged parts are replaced.
Please call Customer Service for assistance.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
Do not at any time let brake liquids, gasoline, petroleumbased
products, penetrating oils, etc., come in contact with plastic
parts. Chemicals can damage, weaken or destroy plastic
which may result in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an authorised service centre.
STORAgE
STORiNg THE PRODUCT
■ Remove the battery pack from the unit before storing.
■ Clean all foreign material from the unit.
■ Store it in a place that is inaccessible to children.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
■ Store and charge your batteries in a cool area.
Temperatures above or below normal room temperature
will shorten battery pack life.
■ Never store batteries in a discharged condition. Store
battery packs in a 30%-50% charged condition.
■ Store the battery pack where the temperature is below
27 FIC and away from moisture.
■ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your unit for long periods of time without using it,
charge the pack as normal every six months of storage.
This practice will prolong battery pack life.
ENViRONMENTAL PROTECTiON
1) Environmental protection should be a priority of
considerable importance when using the machine, for the
benefit of both social coexistence and the environment
in which we live. Try not to cause any disturbance to the
surrounding area.
2) Scrupulously comply with local regulations for the disposal
of packaging, deteriorated parts or any elements with a strong
environmental impact; this waste must not be disposed of as
normal waste, it must be separated and taken to specified
waste disposal centres where the material will be recycled.
3) Scrupulously comply with local regulations for the disposal
of waste materials after mowing.
70
WARNiNg
WARNiNg