Tabla de contenido
Idiomas disponibles
Idiomas disponibles
KEY DiMENSiONS
AND SPECiFiCATiONS
Description
Front-Loading
Washer
Rated Voltage/Frequency
120VAC, 60Hz
Dimensions
27 in" (W) x293/4
in" (D) ×3811/11 in" (H), 51 in" (D, door open)
68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.5 cm (D, door open)
Net Weight
190.1271b(86.24kg)
CHOOSE
THE PROPER LOCATION
WARNING
* This washer
is heavy.
Two or more people are required
when
moving and unpacking
the washer.
Failure to do so
may result in damage
to property
or serious bodily
harm.
* Store and install the washer
where
it will
not be exposed
to temperatures
below
freezing or exposed to outdoor
weather
conditions.
Failure to follow
this warning
can cause
serious injury, fire, electric
shock, or death.
* Properly ground washer
to conform
with all electrlc
governing codes and ordinances.
Failure to follow
this
warning
can cause serious injury, fire, electric
shock, or
death.
* To reduce the risk of electric shock, do not install the
washer
in humid
spaces. Failure to follow
this warning
can
cause serious injury, fire, electric
shock, or death.
* To ensure proper air flow, do not block the large opening
on the bottom
of the washer
with carpeting
or other
materials.
* Do not remove
ground
prong. Do not use an adapter
or extension cord. Plug into a grounded
3=prong outlet.
Failure to follow
this warning
can cause serious injury, fire,
electric
shock, or death.
Power Outlet
° The power outlet must be within
60 in. (1.5 m) of either side
of the washer.
* The appliance
and outlet must be positioned
so that the
plug is easily accessible.
° Do not overload
the outlet with more than
one appliance.
° The outlet must be grounded
in accordance
with current
wiring electric
codes and regulations.
* Time-delay
fuse or circuit
breaker
is recommended.
NOTE:
It is the personal
responsibility
and obligation
of
the product
owner
to have a proper
outlet
installed
by a
qualified
service
technician.
FLOORING
° To minimize
noise and vibration,
the washer MUST be
installed on a solidly
constructed
floor. See the NOTE to
your right.
° Allowable
slope under the entire washer is a maximum
1 in.
difference
from side to side or from front to back.
° Installing
on carpeting
and soft tile surfaces is not
recommended.
° Never install the washer on a platform
or weakly
supported
structure.
CLEARANCES
22 1/4"
(57 cm)
I..,9!
29 3/4'_
_
I_
4"
(75.6 cm)
(10 cm)
51"
(129.5 cm)
To ensure sufficient clearance for water lines and airflow,
allow minimum clearances
of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or floor moldings that may increase the
required clearances.
1,
1,
(2.5 cm)
(68.6
cm)
(2.5 cm)
Allow
at least 21 1/4 in. (54 cm) in front
of
the washer
to open
the door.
NOTE: The floor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without
flexing or bouncing.
If your floor has too much
flex, you may need to reinforce it to make it more rigid.
A floor that is adequate
for a top-loading
washer may
not be rigid enough for a front loading
washer, due to
the difference
in the spin speed and direction.
If the
floor is not solid, your washer may vibrate and you may
hear and feel the vibration
throughout
your house.
7
Tabla de contenido
