Liste De Pièces Detachées - Speedaire 1ZMG5 Manual Del Usuario

Speedaire ® Operating Instructions and Parts Manual
Speedaire ® Paint Tank
General Safety Information Assembly
(Continued)
NOTE: Use PTFE thread sealant tape or
13. Regularly check to be sure gauge and thread sealant on all connections.
regulator are functioning correctly.
1. Assemble the regulator to the paint
Also check that no paint or other
tank lid as shown in Figure 1:
deposits are in the safety valve inlet.
E
In the event more than 50 psi is
N
applied to the tank and the safety
G
valve is clogged, the higher pressure
L
could damage the tank or result in
I
injury.
S
Do not
H
spray
flammable materials in vicinity
of open flame or near ignition
sources including the
Figure 1
compressor unit.
14. Do not smoke when spraying paint,
a. With arrow pointed down and
insecticides, or other flammable
knob toward you, place the gauge
substances.
in the left 1/8 NPT regulator port.
15. Use a face mask/respirator
b. Assemble the 1/8 plug into opposite
when spraying and spray
1/8 NPT regulator port.
in a well ventilated area to
c. Thread the 1/4 T-fitting into the top
prevent health and fire
1/4 inch regulator port.
hazards.
d. Thread 1/4 inch pipe nipple into
16. Do not direct paint or other sprayed
bottom 1/4 inch regulator port
material at the compressor. Locate
(with arrow).
compressor as far away from the
spraying area as possible to minimize e. Thread this assembly into the
overspray accumulation on the 1/4 NPT port on tank lid.
compressor.
17. When spraying or cleaning with
solvents or toxic chemicals, follow the
instructions provided by the chemical
manufacturer.
Failure to follow
instructions on
proper assembly and use of a paint tank
may possibly result in damage to property
or personal injury. This unit must be
assembled as indicated in these
instructions. Only parts supplied with this
unit should be used. These parts are safety
performance engineered. Use only OEM
replacement components.
Material tube
Figure 2
NOTE: This regulator is a special pressure
limiting regulator. Do not use any other
type of regulator with this paint tank.
Assemble the regulator to the paint tank
only as instructed.
2. Assemble the safety relief valve to the
tank lid port.
3. Thread the handle into the center
port of the tank lid.
4. Install hose connector in tank lid port
from the top.
5. The material tube is pre-assembled to
the tank.
EQUIPMENT USE
TO USE A SPRAY GUN
1. Attach the air supply hose (not
Included) to the 1/4 NPT T Fitting.
2. Attach an air hose between the
opposite side of the T Fitting and the
spray gun air inlet.
To Spray
Gun
Air
Supply
Figure 3
Handle
NOTE: A 15 foot air hose and 15 foot
material hose between the paint tank
Hose
connector and spray gun is recommended. Up to 25
feet of air hose may be used between the
paint tank and the compressor. A longer
length may create a large pressure drop.
3. Attach a material hose between the
paint tank connection and the spray
gun material inlet.
Use of a material
Safety
hose that is not
relief
compatible with the solvents being used
valve
could result in damage or serious injury.
2
1ZMG5 Speedaire Instructions d'Utilisation et Manual de Pièces
®
Liste de Pièces Detachées
S'il vous plaît fournir l'information suivante:
-Numéro de modèle
-Numéro de série (si présent)
-Description et numéro de la pièce
Numéro de
Référence
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
NÉCESSAIRE DE PIÈCES DE RECHANGE
L
F
pièces fournies avec ce modèle. Ces pièces sont fabriquées
pour ce réservoir à peinture en qualité d'ingénieur pour la
sécurité et le rendement. Utiliser seulement les pièces de
rechange OEM .
soient bien serrés avant de pressuriser
le réservoir.
Description
Poignée du couvercle de réservoir
Soupape de sûreté, 6,4 mm (1/4 po) NPT
Raccord de tuyau, 9,5 mm (3/8 po) NPS
Couvercle du réservoir à peinture
Joint étanche du couvercle
Tuyau flexible de matériaux, 9,5 mm (3/8 po) NPS
Réservoir galvanisé avec décalques
Manomètre, 3,2 mm (1/8 po) NPT
Régulateur de pression, 0 - 345 kPa
Mamelon de tuyau, 6,4 mm (1/4 po) NPT
Raccord de 6,4 mm (1/4 po) NPT T
Bouchon, 3,2 mm (1/8 po) NPT
avec tête creuse hexagonale, 4,8 mm (3/16 po)
Tuyau flexible de matériaux de 4,6 M,
9,5 mm (3/8 po) NPS EPDM
Tuyau flexible de matériaux de 4,6 M,
6,4 mm (1/4 po) NPS Plastique
Boulon à oreilles
Loquet
Goupille
Bague en E
Nécessaire de loquet
Artículo estándar de ferretería
Ce modèle doit être monté selon ces
instructions. Utiliser seulement les
Assurer que les écrous et boulons
7 Fr
1ZMG5
Numéro de Pièce Quantité
PT001200AV 1
V-215101AV 1
HF180200AV 1
PT282100AV 1
PT282200AV 1
PT006700AV 1
PT282300AV 1
GA231300AV 1
RE011300AV 1
ST016800AV 1
ST160100AV 1
F
1
HA633000AV 1
HA632900AV 1
L
1
L
1
L
1
L
1
PT282900AV 4
F
R
A
N
Ç
A
I
S
®