American Standard LOFT Right Height 2535 Instrucciones De Instalación
American Standard LOFT Right Height 2535 Instrucciones De Instalación

American Standard LOFT Right Height 2535 Instrucciones De Instalación

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTALLATION INSTRUCTIONS
LOFT
®
1.28 GPF ONE-PIECE TOILET
Model 2535 – Compact Elongated Right Height™ with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly,
please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your
installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
FINISHED WALL
7-3/16"
(183 mm)
C/L OF SEAT POST HOLES
140mm (5-1/2" CENTERS)
10-3/16"
(259 mm)
12"
(305 mm)
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 3
Adjustable Wrench
Flexible Supply Tube
28-7/16"
(723 mm)
18-1/2"
(470 mm)
SUPPLY
AS
REQ'D
*10"
(254mm)
FINISHED
11-15/16"
FLOOR
(303 mm)
WAX RING
3
14"
(355 mm)
14-7/16"
(366 mm)
14"
(356 mm)
INSTALL CLOSET BOLTS
9-5/16"
Install closet bolts in flange channel, turn 90 ° , and slide
(236 mm)
into place 6" (152 mm) apart and parallel to wall.
5
WASHER
BOLT
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
Sealant
Tape Measure
Closet Bolts
Carpenters Level
CLOSET FLANGE
CLOSET BOLTS
NUT
A
FLANGE
7302010- 100 Rev. A
Tabla de contenido
loading

Resumen de contenidos para American Standard LOFT Right Height 2535

  • Página 5: Inodoro De 1 Pieza 1.28 Gpf

    Model 2535 – Compact Elongated Right Height™ with Seat Gracias por seleccionar American Standard – el parámetro de primera calidad por más de 100 años. Para asegurar la instalación apropiada de este producto, lea cuidadosamente estas instrucciones antes de empezar. (Ciertas instalaciones pueden requerir asistencia profesional.) También asegúrese de que su instalación cumpla con los códigos locales.
  • Página 6: Instalación Del Inodoro

    INSTALACIÓN DEL INODORO a. Alinee el inodoro con la pared y, con un movimiento de vaivén, presione la taza completamente sobre el anillo de cera y el reborde. De manera alternada, apriete las tuercas hasta que el inodoro quede firmemente asentado en el piso. PERNO DEL CONECTOR PRECAUCIÓN: ¡NO APRIETE EXCESIVAMENTE LAS...
  • Página 7: Cuidado Y Limpieza

    Este daño puede causar fugas y daño a la propiedad. American Standard no será responsable por ningún daño a los herrajes del tanque causado por el uso de limpiadores que contengan cloro (hipocloruro de calcio).
  • Página 8: Guía De Localización De Fallas

    Cierre el suministro del agua. Remueva la tapa y límpiela de acuerdo a la Figura 12. En Canadá: En México: En los Estados Unidos: AS Canada ULC Gerente de servicio al cliente American Standard Brands AS Maquila, S.A. de C.V. P.O. Box 6820 2480 Stanfield Rd. Vía Morelos #330 Piscataway, New Jersey 08855 Mississauga, Ontario Col.

Tabla de contenido