Care And Maintenance - Kärcher FC 3d Cordless Manual De Instrucciones

Storing the Appliance
ATTENTION
To prevent odours developing, the fresh water and
waste water tank must be completely emptied prior to
storing the appliance.
Allow wet rollers to dry in the air (e.g. on the parking sta-
tion), do not place wet rollers in closed cupboards to dry.
Illustration
 Place the device in the parking station.
Illustration
 Press the handle release mechanism.
 Pull the handle upwards.
 Hook the handle to the appliance using the strap.
Illustration
 Place the wet rollers on the parking station to dry.
 Store the appliance in a dry room.

Care and maintenance

DANGER
Illustration
The device contains electrical components and must
therefore never be held under running water or im- mersed in a container containing water - even for clean-
ing the device.
ATTENTION
Illustration
To clean the device, remove the individual components
(floor head cover, fresh water tank, waste water tank
and rollers) and clean them separately. Wipe down the
rest of the device with a moist cloth.
Clean the waste water tank
ATTENTION
The waste water tank must be cleaned regularly to en-
sure that dirt does not accumulate in the tank.
ATTENTION
Do not clean the floor head cover in a dishwasher: The
basic function of the device can be impaired if the floor
head cover is distorted by the dishwasher and the wiper
edge no longer presses correctly onto the rollers. This
will produce a worse cleaning result.
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Place the device in the parking station.
Figure to
 Remove the waste water tank from the appliance.
See Chapter "Emptying the waste water tank".
 Clean the floor head cover, waste water tank and
waste water tank flaps with tap water.
 The flaps of the two waste water tank chambers
can be removed and cleaned separately.
 Alternatively, the waste water tank and waste water
tank flaps can be cleaned in a dishwasher.
Note
The rubber inlays of the waste water tank flaps can be-
come sticky when washed in a dishwasher. This does
not affect their sealing ability.
Figure to
 Also clean the rollers if the device is not going to be
used further.
See chapter "Cleaning the rollers".
Illustration
 After cleaning, fit the waste water tank with flaps
and floor head cover back into the device.
Cleaning the floor head
ATTENTION
Clean the floor head if dirty.
ATTENTION
Do not clean the floor head cover in a dishwasher: The
basic function of the device can be impaired if the floor
head cover is distorted by the dishwasher and the wiper
edge no longer presses correctly onto the rollers. This
will produce a worse cleaning result.
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Place the device in the parking station.
Illustration
 Actuate the floor head cover latch.
 Remove the floor head cover.
Illustration
 Rinse off the floor head cover under running water.
 Clean the waste water tank and rollers.
See chapter "Cleaning the waste water tank".
See chapter "Cleaning the rollers".
 Clean the roller drive with a moist cloth.
Illustration
 Insert the floor head cover into the floor head.
Cleaning the rollers
ATTENTION
The rollers should be washed under a tap or cleaned in
a washing machine after each use to prevent accumu-
lation of detergent residues in the rollers that can lead
to the formation of foam over time.
The fresh water tank and waste water tank must be
emptied if the device is laid on the floor in order to re-
move the rollers. This prevents liquids from escaping
from the tanks while the device is lying on the floor.
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Place the device in the parking station.
Illustration
 Twist out the cleaning rollers from the recessed
grip.
Illustration
 Clean the cleaning rollers under running water.
or
 Wash the cleaning rollers in the washing machine
up to 60°C.
ATTENTION
Do not use any soft detergents when cleaning in the
washing machine. This avoids causing damage to the
microfibres. It also preserves the high performance lev-
els of the cleaning rollers.
The cleaning rollers are not suitable for the tumble dry-
er.
Figure to
 Once cleaned, place the rollers on the cleaning sta-
tion storage and leave them to air dry.
 Drying time can be minimized by wringing out the
rollers beforehand.
 Also clean the floor head cover and waste water
tank if the device is not going to be used further.
 Clean the roller drive with a moist cloth.
– 12
EN 29