Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
This will prevent the saw from jumping or vibrating and
will minimize blade breakage.
Flush Cutting (Fig. G)
The compact design of the recipro cating saw motor
housing and pivoting shoe permit close cutting to floors,
corners and other difficult areas.
1. To maximize flush cutting capabilities, insert the blade
shaft into the blade clamp with the teeth of the blade
facing up.
2. Turn the saw upside down so you are as close to the
work surface as possible.
Wood Cutting (Fig. H)
When cutting wood, use speed 2 to maximize performance.
1. Before cutting any type of wood, be sure the workpiece
is firmly anchored or clamped to prevent slipping.
2. Place blade and pivoting shoe firmly against work
to be cut.
3. Switch on saw motor before starting the cut.
4. Always hold saw firmly with both hands while cutting.
Whenever possible, the pivoting shoe must be held
firmly against the material being cut. This will prevent
the saw from jumping or vibrating and minimize
blade breakage.
Metal Cutting (Fig. I)
When cutting metal, use speed 1 to maximize blade life.
1. Use a finer blade for ferrous metals and a coarse blade
for non-ferrous materials.
2. In thin gauge sheet metals it is best to clamp wood to
the underside of the sheet. This will ensure a clean cut
without excess vibration or tearing of metal.
3. Avoid forcing cutting blade as this reduces blade life
and causes costly blade breakage.
nOTE: You should spread a thin film of oil or other coolant
along the line ahead of the saw cut for easier operation
and longer blade life. For cutting aluminum, kerosene
is preferred.
Pocket Cutting - Wood Only (Fig. J)
Measure the surface area to be cut and mark clearly with a
pencil, chalk or scriber.
1. Insert blade in blade clamp and tighten blade
clamp securely.
2. Tip the saw backward until the back edge of the
pivoting shoe is firmly on the work surface.
3. Switch motor on, permitting blade to attain
maximum speed.
4. Grip handle steadily and begin a slow, deliberate
upward swing with the handle of the saw.
5. The blade will begin to feed into material. Always
be sure blade is completely through material before
continuing with pocket cut.
NOTE: In areas where blade visibility is limited, use the
edge of the pivoting shoe as a guide.
8
Project Tips
•
Cut only with sharp blades; they cut cleaner, faster and put
less strain on the motor while cutting.
•
When cutting, always ensure that the pivoting shoe
is resting against the workpiece. This will improve
operator control and minimize vibration.
•
For longer blade life, use bi-metal blades or carbide
tipped blades. These utilize a carbon steel back welded
to high speed steel teeth making the blade more
flexible and less prone to breaking.
Worklight (Fig. A)
The worklight
is activated when the trigger switch is
11
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1-888-331-4569 .
Versatrack™ (Fig. K)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
Tabla de contenido
