Assembly & Set-Up - MTD 19A70063OEM Manual Del Operador

Disengage the PTO, engage the brake lock, and stop the tractor engine
before performing any preparation procedures. Place the tractor on a firm
and level surface before beginning installation procedures.
The exhaust system and surrounding areas are HOT. To avoid personal
injury, allow the tractor to cool before beginning any plow installation or
removal procedures.
NOTE: The hardware used to install some components on the all season plow has been
loosely installed for shipping purposes. To assemble the plow it may be necessary to remove
this hardware to complete installation.
NOTE: Recommend removing the deck for all models and setting arms in parking brake
position.
Attach Mounting Plates To Tractor
NOTE: Top plate location differs by model. To identify correct positioning, see Figure 1. ZT
1. Place the two top plates (789-
03137) on top of tractor foot
pan as shown and secure with
four hex screws (710-3015)
and four flat washers (736-
0173) from hardware pack
689-02139. See (1) in Figure 2.
TIP:
May be necessary to have two
people to perform this step. One to
secure the plates, and one to lift front
of the tractor.
2. Bring larger plate (689-02121)
up from bottom of foot pan, aligning holes with hex screws and flat washers
placed in Step 1. Secure assembly with four flange lock nuts (712-04064)
from hardware pack 689-02139 and tighten until flush. See (2) in Figure 2.
NOTE:
Flanged side of larger plate should be facing down and curving away from the tractor.
NOTE:
Once installed, plates can remain on tractor. They will not affect function when deck
is reinstalled.
Install "H" Bracket
1. Install "H" bracket assembly
(689-02119) to larger plate
(689-02121) mounted to
underside of foot pan by facing
longer arms of "H" bracket
toward plate, aligning holes in
arms with holes in U brackets
on larger plate. See Figure 3.
2. Working from inside out,
secure plate and "H" bracket
together with two clevis pins
(711-05217) and two bow tie
pins (714-05005) from hardware pack 689-02139. See Figure 3.
3. Let "H" bracket assembly hang loose.
ASSEMBLY & SET-UP
WARNING
WARNING
Z / XP / CZT ZTX
Figure 1
1
Flanged end down
Figure 2
Figure 3
Install Front Mounting Bracket
IMPORTANT: The frame mount hardware installed on the front mounting bracket is for ZT
models only. For ZTX models, remove 4 rubber spacers and associated hardware prior to
attaching large mounting bracket to tractor frame. See circles and note in Figure 4.
1. Mount front mounting bracket
assembly (689-02459) by
aligning rear of assembly with
front of tractor and sliding
upper lip over and lower lip
under frame. See Figure 4.
2. Working from the bottom
up, secure bracket to tractor
frame with two carriage bolts
(710-1649), two spacers (750-
06527) and two wing knobs
(720-04186) from hardware
pack 689-02139. See Figure 4
inset.
NOTE:
Hole placement differs
between models. Use inner holes for ZT
models and outer holes for ZTX models.
See Figure 4.
3. Swing "H" assembly bracket
previously installed up to meet
front mounting bracket. See
Figure 5.
NOTE:
"H" bracket assembly arms
should fit between the two sets
of U-channels on backside of front
mounting bracket. See Figure 5.
4. Working from the inside out,
secure with two clevis pins
(711-05217) and two bow tie pins
(714-05005) from hardware pack
689-02139. See Figure 5 inset.
2
5. Insert flanged bearings (741-0192)
from hardware pack 689-02139
into front mounting bracket. See
Figure 6.
Attaching Plow and Lift
Handle Assemblies
1. Bring plow assembly
(689-02100) up from
underneath front
mounting bracket (689-
02459) and fit between
flanged bearings (741-
0192). See (1) in Figure 7.
TIP:
May be necessary to have
two people to perform this step.
2. Holding plow assembly in
place, slide lift handle
assembly (689-02499) into
position, making sure to
slide shaft through both
bearings. See (2) in Figure 7.
4
Remove for ZTX
Models
Figure 4
Figure 5
Figure 6
2
1
Figure 7