Tabla de contenido
Idiomas disponibles
Idiomas disponibles
STEAM LANCE
with vacuum. Pay attention when cleaning delicate
surfaces, start the steam release maintaining a
minimum distance of 20-40cm and then bring it
closer depending on the desired result and the
treated surface.
TANK SUCTION ACCESSORY
MICROFIBER CLOTH
the steam dispensed and reduces the friction of the
brush during the treatment
BRUSHES
These brushes
must be connected to the STEAM
LANCE. They are used to remove
resistant dirt and for deep cleaning,
even in the corners or small spaces.
Choose the most suitable type (ø28,
40, 60 mm) according to the surface
to be treated.
MANTAINANCE
* Always remove the plug before cleaning
or carrying out operations on the machine.
* End user must not open or dismantle the
.
machine
For the safety of the operator and to always ensure a
perfect performance, we recommend the following
checks and maintenance:
AFTER EVERY USE:
For a correct cleaning, it is advice to clean the machine
and its accessories with a clean cloth moistened only
This accessory can be
applied directly to the
flexible. Suitable for having
a powerful jet of steam
conveyed the nozzle exit.
For a perfect result it can
be used together with the
suction nozzle, so that you
can dry the cleaned surface
Accessory to be connected
to the flexible hose to
vacuum and clean the
tanks.
Cloth to be used hooked
with the multi-purpose
brush to clean delicate
surfaces, such as
wooden floors, furniture,
etc. It offers a great
absorption power,
reduces the power of
(End user)
with a few drops of water. Do not use alcohol or other
solvents,
they
components.
To maintain efficient and easy to couple the accessories,
check the o-ring seal (steam sealing gaskets) and
possibly wet them with a little silicone grease.
VACUUM FUNCTION: when you finish to vacuum, it is
advisable to vacuum some water to clean the conducts
and the filter. Afterwards, dry the bucket or do not totally
close it so that it will dry itself.
PERIODICALLY:
Periodically check that the power cord does not show
signs of wear or aging. If it is damaged, it is absolutely
necessary to get it replaced by specialized personnel
before being able to re-use the appliance again.
BOILER CLEANING
Once a year a check and boiler cleaning must be carried
out in our authorized centers.
RINSE: It's recommended at least every 50 hours of
operation or 2 months.
a) DISCHARGE: The machine must be cold or definitely
discharged from the steam pressure and the plug
disconnected (see pressure gauge (4a)). It is possible to
use the Boiler-Off switch (6) to completely discharge the
steam from the boiler: With the machine switched on,
turn off the Boiler-Off switch (6), insert the hose into the
machine's socket (5) and pressing the button (10)
completely dispense all the residual steam in the boiler.
(keep the dispensing active for a further minute after the
apparent steam escapes to ensure that the boiler has
been completely emptied) (see pressure gauge (4a)).
With the help of a wrench CH 21 unscrew the cap (15)
placed under the machine in correspondence of the
boiler (see image). After having taken off the cap, shake
slightly the machine to let the water and the dissolved
limestone out.
When the boiler is empty, clean and close carefully the
cap tightening it with the wrench.
b) FILLING: Fill the water tank (7), turn the machine on
and make it start again, waiting for the boiler to be re-
charged again.
(att: it may be that during the first charge cycle, the "end
of water" light turns on and you need to shut down/restart
the machine to complete the load)
BOILER AND TANK CLEANING:
"-SEr": The notice for cleaning the boiler is indicated
on the machine display, every 300 liters of water
consumed, and is repeated when the machine is
started until cleaning is performed and the Service
reset is followed. The cleaning of the boiler is however
recommended at least once every 6 months.
16
may
damage
the
plastics
(End user)
15
and
Tabla de contenido
