COMFORT-AIRE RG Serie El Manual Del Propietario página 29

Owner's Manual - RG/RADS Series
AIR CONDITIONER FEATURES
TO ADJUST FAN SPEEDS:
Press Fan button to select the Fan Speed in four
steps-Auto, Low, Med or High. Each time the button
is pressed, the fan speed mode is shifted.For some
models, the fan speed can not be adjusted under
HEAT mode. On Dry mode,the fan speed is
controlled at Low automatically.
SLEEP FEATURE:
Press Sleep button to initiate the sleep mode. In this
Press Sleep button to initiate the sleep mode. In
this mode the selected temperature will increase
mode the selected temperature will increase (cooling)
(cooling) or decrease (heating) by 2•• F /1(or 2)
or decrease (heating) by 2°F/1 (or 2)°C 30 minutes
minutes after the mode is selected. The
after the mode is selected. The temperature will then
temperature will then increase (cooling) or
increase (cooling) or decrease (heating) by another
decrease (heating) by another 2•• F/1(or 2)
2°F/1 (or 2)°C after an additional 30 minutes. This
an additional 30 minutes.•• T his new temperature will
new temperature will be maintained for 6 or 7 hours
be maintained for 6 or 7•• h ours before it returns to
before it returns to the originally selected temperature. the•• o riginally selected temperature. This ends the
Sleep mode and the unit will continue to operate as
This ends the Sleep mode and the unit will continue
originally programmed. The Sleep mode program
to operate as originally programmed. The Sleep mode
can be canceled at any•• t ime during operation by
program can be cancelled at any time during operation
pressing the Sleep button•• a gain.
by pressing the Sleep button again.
CHECK FILTER FEATURE:
Press Check filter button to initiate theis feature.
This feature is a reminder to clean the Air Filter for
more efficient operation. The LED(light) will illumi-
nate after 250 hours of operation. To reset after
cleaning the filter, press the Check Filter button and
the light will go off.
ENERGY SAVER FEATURE:
Press Energy saver button to initiate this function.
This function is available on COOL, DRY, AUTO
(only AUTO-COOLING and AUTO-FAN) modes.The
fan will continue to run for 3 minutes after the
compressor shuts off.The fan then cycles on for 2
minutes at 10 minute intervals until the room
temperature is above the set temperature, at which
time the compressor turns back on and Cooling
Starts.
FOLLOW ME FEATURE:
Follow
Me
This feature can be activated from the remote
control ONLY. The re mote control serves as
a remote thermostat allowing for the precise
temperature control at its location.
To activate the Follow Me feature, point the remote
control towards the unit and press the Follow Me
button. The remote display is actual temperature at
its location. The remote control will send this signal
to the air conditioner at 3 minute intervals until pressing
to the air conditioner 3 minute interval• • until
the Follow Me button again. If the unit does not receive press•• • • • • the Follow Me button again.•• If the unit
does not receive the Follow Me signal during any 7
the Follow Me signal during any 7 minute interval, the unit
minute interval, the unit will beep to indicate the
will beep to indicate the Follow Me mode has ended.
Follow Me mode has ended.
O O C 30
O O C after
(on some models)
Light flashes or
illuminates
TO SELECT THE OPERATING MODE:
To choose operating mode, press Mode button. Each
To choose operating mode, press Mode button.•• Each
time you press the button, a mode is selected in a
time you press the button, a mode is selected in a
sequence that goes from Auto, Cool, Dry, Heat (cooling
sequence that goes from Auto, Cool, Dry ,heat(cooling••
only models without)and Fan. The indicator light beside
only models without) and Fan. The indicator light beside
will be illuminated and remain on once the mode is
will be illuminated and remain on once the mode is
selected.
selected. The unit will automatically initiate the Energy
The unit will • • •• • • • • • • • ••• • • • •
Saver function under Cool, Dry, Auto (only Auto-Cooling
function under Cool, Dry, Auto(only Auto-Cooling and
and Auto-Fan) modes.
Auto-Fan) modes.
To operate on Auto feature:
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling only models
without), or fan only operation depending on what
temperature you have selected and the room temperature.••
The air conditioner will control room temperature
automatically round the temperature point set by you.
In this mode, the fan speed cannot be adjusted, it starts
automatically at a speed according to the room
temperature.
To operate on Fan Only:
Use this function only when cooling is not desired,such
as for room air circulation or to exhaust stale air(on
some models). (Remember to open the vent during this
function, but keep it closed during cooling for maximum
cooling efficiency.) You can choose any fan speed you
prefer.
During this function, the display will show the actual
During this function, the display will show the actual••
room temperature, not the set temperature as in the
room temperature, not the set temperature as in the••
cooling mode.
cooling mode
In Fan only mode, the temperature can not be adjusted. In Fan only mode ,the temperature • • • • • • not • • ••••
To operate on Dry mode:
In this mode, the air conditioner will generally operate
in the form of a dehumidifier. Since the conditioned
space is a closed or sealed area, some degree of
cooling will continue.
TIMER: AUTO START/STOP FEATURE:
Press Timer button, the TIMER ON or TIMER OFF indicator
light illuminates. It indicates the Auto Start or Auto Stop
program is initiated. For some units, keep pressing the
Timer button cancel the timer settings.
Timer button to cancel the timer settings.
Press or hold the UP or DOWN button to change the Auto
time by 0.5 hour increments, up to 10 hours,then at 1 hour
increments up to 24 hours.The control will count down the
time remaining until start.
The selected time will register in 5 seconds, and the system
will automatically revert back to display the previous
temperature setting or room temperature when the unit is
on.(when the unit is off,there is no display.)
Turning the unit ON or OFF at any time or adjusting the
timer setting to 0.0 will cancel the Auto Start/Stop timed
program.
27
• ••• • • • • •• i nitiate the Energy Saver
adjusted.