Operation - EINHELL HEROCCO Manual De Instrucciones

bits which are suitable for the purpose and in
faultless condition.
3. Using a cable/pipe detector, check the area
you want to work on for concealed electric
cables and gas and water pipes.
5.1 Additional handle (Fig. 2/Item 10)
For safety reasons you must only use the
impact drill with the additional handle.
The additional handle (10) enables you to achieve
better stability whilst using the impact drill. For
safety reasons the machine must not be used
without the additional handle (10).
The additional handle (10) is secured to the
impact drill by a clamp. Turning the handle anti-
clockwise (viewed from the handle) will release
the clamp. Turning the handle clockwise tightens
the clamp.
Release the clamp of the additional handle fi rst.
Then you can swivel the additional handle (10)
into the most comfortable working position for
yourself. Now turn the additional handle (10) in
the opposite direction again until the additional
handle (10) is secure.
5.2 Fitting and adjusting the depth stop (Fig.
3/Item 11)
The depth stop (11) is held in position by a
number of locking points.
•
Press the button (a) and keep it pressed while
pushing the depth stop (11) into the guide.
•
Set the depth stop (11) to the same level as
the drill bit.
•
Pull the depth stop back by the desired
drilling depth and then release the button (a).
•
The depth stop (11) will now have been
locked in position automatically.
•
Now drill the hole until the depth stop (11)
touches the workpiece.
5.3. Inserting a tool (Fig. 4)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the equipment.
•
Clean the tool before fitting it and apply a thin
coating of bit grease to the tool shaft.
•
Turn and push the dust-free tool into the tool
mounting (b) as far as it will go. The tool will
lock automatically.
•
Check that the bit is locked in placed by
pulling on it.
Anl_Herocco_4513975_SPK7.indb 23 Anl_Herocco_4513975_SPK7.indb 23
GB
5.4. Removing a tool (Fig. 5)
Pull back and hold the locking sleeve (1) and
remove the tool.

6. Operation

6.1 Charging the LI battery pack (Fig. 6/7)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (6) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(8) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery
charger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 23 -
21.10.2020 15:54:35 21.10.2020 15:54:35