Making The Electrical Connection - Home Decorators Collection 26666 Guía De Uso Y Mantenimiento

Assembly - Hanging the Fan (continued)
8

Making the electrical connection

WARNING: Each wire nut supplied with this fan is designed to
accept up to one 12-gauge house wire and two wires from the
fan. If you have larger than 12-gauge house wiring or more
than one house wire to connect to the fan wiring, consult an
electrician for the proper size wire nuts to use.
IMPORTANT: Use the wire connecting nuts (BB) supplied with
your fan. Secure the connectors with electrical tape and ensure
there are no loose strands or connections.
NOTE: The fan comes with 54 inch lead wires for use with an
extended ball/downrod assembly. If using the 4.5 inch ball/
downrod assembly (B) provided, you can cut the lead wires to
your desired length (no shorter than 12 inches).
□
Connect the ground conductor of the 120-Volt supply (this
may be a bare wire or a wire with green colored insulation) to
the green ground lead(s) (II) of the fan.
□
Connect the fan motor white wire (LL) to the receiver (NN) white
wire (LL) using a wire connecting nut (BB).
□
Connect the fan motor black wire (KK) to the receiver (NN)
black wire (KK) using a wire connecting nut (BB).
□
Connect the fan motor blue wire (JJ) to the receiver (NN) blue
wire (JJ) using a wire connecting nut (BB).
□
Connect the receiver (NN) red wire (OO) to the supply black
(hot) wire (KK) using a wire connecting nut (BB).
□
Connect the receiver (NN) white wire (LL) to the supply white
wire (neutral) (LL) wire using a wire connecting nut (BB).
□
After connecting the wires, spread them apart so that the
green (II) and white wires (LL) are one side of the outlet box
(MM) and the black wire (KK) is on the other side.
□
Turn the wire connecting nuts upward, and carefully push the
wiring into the outlet box (MM).
JJ
KK
MM
NN
LL
LL
9
Mounting the fan
WARNING: When using the standard ball/downrod mounting, the
tab in the ring at the bottom of the mounting bracket must rest in
the groove of the hanger ball. Failure to properly seat the tab in
the groove could cause damage to the wiring.
□
Align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots, and turn clockwise to lock the canopy (C) in place.
□
Firmly tighten the two mounting screws (O).
□
Install the remaining two mounting screws (O) into the holes
in the canopy (C) and tighten firmly.
□
Install the decorative canopy ring (K) by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock it in place.
A
Close-to-Ceiling mounting
WARNING: The locking slots of the celling canopy are provided only
as an aid to mounting. Do not leave the fan assembly unattended
until all four canopy screws are engaged and firmly tightened.
□
Carefully unhook the fan from the mounting bracket (A) and
align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock the canopy (C) in place. Im-
mediately tighten the two mounting screws (O) firmly.
□
Install the remaining two mounting screws (O) into the holes
in the canopy (C) and tighten firmly.
□
Install the decorative canopy ring (K) by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock it in place.
A
10
O
K
C
D
O
K
D