HIKOKI C 3610DRJ Instrucciones De Manejo página 34

English
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not allow
for safe handling and control of the tool in unexpected
situations.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fire when used with another battery
pack.
b) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that
can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modified.
Damaged or modified batteries may exhibit unpredictable
behaviour resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature.
Exposure to fire or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions.
Charging improperly or at temperatures outside the
specified range may damage the battery and increase
the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed by
the manufacturer or authorized service providers.
SAFETY INSTRUCTIONS FOR TABLE
SAW
1) Guarding related warnings
a) Keep guards in place. Guards must be in working
order and be properly mounted.
A guard that is loose, damaged, or is not functioning
correctly must be repaired or replaced.
b) Always use saw blade guard, riving knife and
anti-kickback pawls for every through–cutting
operation.
For through-cutting operations where the saw blade
cuts completely through the thickness of the workpiece,
the guard and other safety devices help reduce the
risk of injury.
c) Immediately reattach the guarding system after
completing an operation (such as rabbeting)
which requires removal of the guard, riving knife
and/or anti-kickback pawls.
The guard, riving knife, and anti-kickback pawls help
to reduce the risk of injury.
d) Make sure the saw blade is not contacting the
guard, riving knife or the workpiece before the
switch is turned on.
Inadvertent contact of these items with the saw blade
could cause a hazardous condition.
e) Adjust the riving knife as described in this instruction
manual.
Incorrect spacing, positioning and alignment can make
the riving knife ineffective in reducing the likelihood of
kickback.
f) For the riving knife and anti-kickback pawls to
work, they must be engaged in the workpiece.
The riving knife and anti-kickback pawls are ineffective
when cutting workpieces that are too short to be
engaged with the riving knife and anti-kickback pawls.
Under these conditions a kickback cannot be prevented
by the riving knife and anti-kickback pawls.
g) Use the appropriate saw blade for the riving knife.
For the riving knife to function properly, the saw blade
diameter must match the appropriate riving knife and
the body of the saw blade must be thinner than the
thickness of the riving knife and the cutting width of the
saw blade must be wider than the thickness of the
riving knife.
2. Safety instructions for sawing procedures
a) DANGER: Never place your fingers or hands
in the vicinity or in line with the saw blade.
A moment of inattention or a slip could direct your
hand towards the saw blade and result in serious
personal injury.
b) Feed the workpiece into the saw blade only against
the direction of rotation.
Feeding the workpiece in the same direction that the
saw blade is rotating above the table may result in the
workpiece, and your hand, being pulled into the saw
blade.
34