Configuration - Vimar Elvox Tab Serie Instrucciones Instalador - Manual Do Instalador

Configurations
Choice of ringtones
10 different ringtones can be selected. Different ringtones can also be set
for outdoor, intercommunicating and door calls (see below). The ringtones
must be selected with the monitor on stand-by and the handset on the hook.
The button for entering configuration mode is button A (self-start).
Button E1 selects the ringtone for ENTRANCE PANEL CALL.
Button E2 selects the ringtone for INTERCOMMUNICATING CALL.
Button E3 selects the ringtone for DOOR CALL (exclusively using the but-
ton interface module 6120 or Vimar landing call button). In the case of a
door call by means of a button connected directly to the monitor's terminals
FP and M, the ringtone cannot be changed.

Configuration:

1) Press button A (self-start) and hold down (for 2 s) until the LED C (lock)
begins flashing and the monitor emits an audible signal.
2) Press and hold down the button for the chosen ringtone (button E1/
button E2/button E3) until the ringtone is heard on the monitor.
3) Press the button repeatedly (button E1/button E2/button E3) to select
the desired type of ringtone.
4) After choosing the desired ringtone, press button A or refrain from tou-
ching any buttons for 5s to save. After completing the configuration, the
LED flashes and then turns off.
Ringtone volume adjustment
The ringtone volume can be set to 6 levels plus mute.
Press button A (self-start) to enter configuration mode.
Press button B (bell) to lower the ringtone volume.
Press button C (key) to increase the ringtone volume.
The ringtone volume must be adjusted with the monitor on stand-by and
the handset on the hook.
Configuration:
1) Press button A and hold down (for 2 s) until the LED C (lock) begins
flashing and the monitor emits an audible signal.
3) Press button B to lower or button C to increase the volume. Each time
the buttons are pressed the volume changes by one level.
4) After choosing the desired volume, press button A or refrain from tou-
ching any buttons for 5s to save. After completing the configuration, the
flashing LED goes off and a "beep" is emitted.
Muting the ringtone (User Away function)
Using the volume adjustment procedure described above, pressing button
B a sufficient number of times results in the ringtone being muted. The
"Ringtone muted" status is indicated by the button B LED (ringtone muted)
lighting up steadily.
If the monitor receives a call from the entrance panel while the ringtone is
muted, this is indicated by the LED/button B emitting one flash for each
unanswered call up to a maximum of 4 calls (these flashes occur every 10
s). When the ringtone volume is restored, at least to its minimum level, this
indication will be reset.
Maintenance
Clean the monitor using a soft cloth, which can be dry or slightly dampened
with water. Do not pour water directly onto the screen and do not use any
type of chemical product.
GB
Installation
Dimensions:
Fig. 3 160 mm
180 mm
External wall mounting
- Install the monitor away from sources of light and heat.
- Fix the monitor coupling plate: directly to the wall by means of two
expansion plugs or to a unified 3-module rectangular flush-mount back
box (Vimar V71303 type) installed vertically or a round flush-mount
back box (60 or 70 mm). Two expansion plugs to be used for fixing
directly to the wall and two screws for fixing to a round flush-mount box
are provided.
- We recommend installing the monitor with its lower edge at a height of
1.40 m from the floor (Fig. 4).
- Remove the terminal block from the bottom of the monitor using a sui-
table screwdriver. Take care to lever the two end terminals and not the
circuit board (Fig. 7).
- Make the connection as shown in the wiring diagrams.
- Reconnect the wired terminal block to the monitor, ensuring that it is
pushed in completely.
- Mount the monitor as follows: position the monitor on the coupling plate
keeping it slightly raised. While keeping the face plate pressed, apply a
light downward pressure until it clicks into place.
- If the monitor needs to be removed, push lightly into the slot (Fig. 6) and
raise it so as to release the monitor from the frame.
Fig. 4
1,40 m
45 mm
13