Technical Specifications - Philips SBC SC467 Manual Del Usuario

ENGLISH
6
Using batteries
Operating the Baby unit cordlessly
1
Remove the battery compartment cover using a coin.
2
Insert four 1.5V, LR6 (AA) batteries noting the + and - configuration
inside the battery compartment.
Batteries not included; we recommend non-chargeable Philips Alkaline
batteries.
3
Put the cover back in place and secure using a coin.
> If the power light flashes (red) install new batteries.
The unit operates for up to 30 hours on batteries.
Replacing the Parent unit's battery pack
1
Open the Parent unit's battery compartment cover.
2
Disconnect the old battery pack from the power plug and remove.
3
Carefully connect the new battery pack to the power plug and place
inside the battery compartment.
4
Close battery compartment cover.
Disposal of batteries
Dispose of used batteries in an environmentally friendly manner.
Do not mix old and new batteries, or different types of batteries.
Remove Baby unit batteries if the baby monitor is not to be used for long
periods.

Technical specifications

Power supply: • Battery pack; rechargeable NiMH for Parent unit (included);
• Optional batteries 4 x 1.5V; AA alkaline for Baby unit (not included);
• AC power adapter 230V AC, 50 Hz (two included): - Output voltage 9V DC, 200mA.
• Only use the AC power adapter included or a type that complies with safety standard EN60950
and that has the following specification: input 230V AC, 50 Hz; output 9 Volt DC / 200mA.
Operating range: • up to 250 metres in ideal conditions (walls, floors, etc. can limit this distance.)
Operating temperature: • 10°C to 40°C
Digital Pilot tone: • Continuous communication link (hidden signal helps reduce interference and ensures a
continuous link between both units so you only hear your baby's sounds).
SBC SC467/00:
Transmission frequencies:
SBC SC467/05 (IRE, UK):
SBC SC467/16 (ES):
from 40.695 to 40.675 MHz
from 49.830 to 40.890 MHz
from 31.000 to 31.350 MHz
Problem solving
Problem Possible cause
Power light does not P P P P P arent unit: arent unit: arent unit: arent unit: arent unit: unit is not turned on.
light.
Batteries are low.
Bab Bab Bab Baby unit: Bab y unit: y unit: y unit: y unit: unit is not turned on.
Power adapter is not plugged in or
batteries are exhausted.
High pitched noise. Units are too close together.
Parent unit batteries Battery life is at an end.
do not charge.
No sound. Volume on parent unit is set too
low.
Power light flashing. Batteries are low or empty.
Talk-back not Loudspeaker volume on Baby unit is
working *. too low.
Intercom function Sensitivity setting on Baby unit still
not working. on.
Interference or poor Mobile or cordless phones too close
reception. to the baby monitor.
Pick-up from another Both systems are operating on the
baby monitor. same frequency.
System check light Units are out of range or there is
flashing (red) / interference from another FM
System check alarm. source.
* With the talk / intercom function if either the parent or baby unit is transmitting, then the other unit can only receive and not transmit.
ENGLISH
7
Solution
Turn VOLUME ON/OFF control
downwards.
Recharge batteries.
Push power button.
Plug in power adapter or replace
batteries.
Move parent unit away from baby
unit. Turn VOLUME ON/OFF
control on parent unit upwards.
Connect charging base to mains
power. Replace battery pack.
Turn VOLUME ON/OFF control
downwards.
Parent unit:- recharge battery pack.
Baby unit:- replace batteries or
connect to mains power.
Set VOLUME control on baby unit to
mid-range.
Set sensitivity on Baby unit to zero.
Move phones away from the units.
Switch channels.
Move units closer together to
restore the link. Remove the other
FM source.