Plastic Bag; How To Change The Bag; Tilting Discharge Device Replacement And Use; Compressor Use And Maintenance - Blastrac BDC-24-230V-P Manual De Instrucciones

Instruction manual BDC-24-230V-P

Plastic bag

You can use the plastic bags supplied by the manufacturer
sales network (Fig. 8).

How to change the bag

WARNING!
■ These operations can only be carried out by
trained and qualified personnel who must wear
adequate clothing, in compliance with the laws
in force.
Take care not to raise dust during these
■
operations. Wear a P3 protective mask.
■ In case of dangerous and/or toxic dust, you
must use the supplied safety bag for these
vacuum cleaners.
■ The bag must only be disposed of by qualified
personnel and in compliance with the laws in
force.
Tilting discharge device replacement
and use
Figure 8A
1. Tilting discharge device assembly
■ Fasten the hopper to the filtering chamber, by inserting
it into the relevant housings and, operating on the lever
(2) to lock it.
■ Insert the bag (Longopac
and fasten its end with the belt (3).
■ Engage the tilting discharge device support to the
hopper by fastening it with the relevant pins.
■ Remove the bag (Longopac
support platform and close its end with the supplied
clamp.
When the bag is full (Longopac
■
with two clamps by fastening them at 50 mm one
from the other, then with a pair of scissors cut the bag
between the two clamps.

Compressor use and maintenance

WARNING!
Refer to the use and maintenance manual, supplied
with the machine documentation, when using or
servicing the compressor.
) into the relevant support
®
) until it lays on the lower
®
) close the upper end
®

At the end of a cleaning session

■ Turn the vacuum cleaner off with switches (2-3-4 - Fig.
4), turn the electric panel (7 - Fig. 5) off and disconnect
the plug from the socket
■ Wind the connection cable up and hang it in the
relevant compartment (Fig. 9).
■ Empty the container as described in the "Emptying the
container" paragraph.
■ Clean the vacuum cleaner as described in the paragraph

"Maintenance, cleaning and decontamination".

■ Wash the container with clean water if aggressive
substances have been vacuumed.
■ Store the vacuum cleaner in a dry place, out of reach of
unauthorised persons.
Maintenance, cleaning and
decontamination
WARNING!
To guarantee the safety level of the vacuum
cleaner, only original spare parts supplied by the
manufacturer should be used.
WARNING!
The precautions described below must be taken
during all the maintenance operations, including
cleaning and replacing of the main and HEPA filters.
WARNING!
The maintenance, cleaning and decontamination
operations must only be performed with the
vacuum cleaner turned off with switch (7 - Fig. 5)
and the plug disconnected from the power socket.
It is absolutely forbidden to perform maintenance
with the plug connected to the socket.
Danger of electric shock!
■ If the user is performing the maintenance operations,
the vacuum cleaner must be disassembled, cleaned
and overhauled as far as reasonably possible without
hazards for the maintenance personnel or other people.
The suitable precautions include decontamination before
disassembling the vacuum cleaner, adequate filtered
ventilation of the exhaust air from the room in which
it is disassembled, cleaning the maintenance area and
suitable personal protection.
A check must be carried out by the manufacturer or
■
the personnel of the same at least once a year. For
example: check the air filters to find out whether the
air-tightness of the vacuum cleaner has been impaired
in any way and make sure the electric control panel
operates correctly.
WARNING!
The procedures for servicing and emptying the
vacuum cleaner including removing the dust
container, must only be performed by specialised
personnel wearing protective clothing. Do not use
without the complete filter system in place.
www.blastrac.com ‒ [email protected]
9/16
I
US