Safety Warnings Common For Grinding Or Abrasive Cutting-Off Operations; Further Safety Instructions For All Operations; Kickback And Related Warnings - Worx WX800 Traducción De Las Instrucciones Originales

Auxiliary handle
2.0Ah Battery(WA3551.1)
1hr Charger (WA3860)
We recommend that you purchase your accessories
from the same store that sold you the tool. Refer to
the accessory packaging for further details. Store
personnel can assist you and offer advice.
SAFETY INSTRUCTIONS
FOR ALL OPERATIONS
SAFETY WARNINGS COMMON FOR GRINDING
OR ABRASIVE CUTTING-OFF OPERATIONS:
a) This power tool is intended to function as
a grinder or cut-off tool. Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
b) Operations such as sanding, wire brushing,
polishing are not recommended to be
performed with this power tool. Operations
for which the power tool was not designed may create
a hazard and cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does
not assure safe operation.
d) The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories running
faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Threaded mounting of accessories must
match the grinder spindle thread. For
accessories mounted by flanges, the
arbour hole of the accessory must fit the
locating diameter of the flange. Accessories
that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess
wear. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and run the
power tool at maximum no-load speed for
Lithium-Ion cordless angle grinder
1 1
2 /
1 /
one minute.Damaged accessories will normally
break apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated by
various operations . The dust mask or respirator must
be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise
may cause hearing loss.
i) Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond
immediate area of operation.
j) Hold the power tool by insulated gripping
surfaces only, when performing an
operation where the cutting tool may
contact hidden wiring. Contact with a "live" wire
will also make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
k) Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
l) Do not run the power tool while carrying it
at your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
m) Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
n) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
o) Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
p) Your hand must hold on the handle when you are
working. Always use the auxiliary handles supplied
with the tool. Loss of control can cause personal injury.
FURTHER SAFETY
INSTRUCTIONS FOR ALL
OPERATIONS

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory's rotation at
the point of the binding.
7
EN