Tabla de contenido
Idiomas disponibles
Idiomas disponibles
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY, the
warranty will not be valid.
Using an Extension Cable
An extension cable should not be used unless absolutely
necessary. Use of an improper extension cable could
resultin a risk of fire and electric shock. If an extension
cable must be used, use only those that are approved by
the country's Electrical Authority. Make sure that extension
cord is in good condition before using. Always use the
cord that is suitable for the power input of your tool (see
technical data on name plate). The minimum conductor
size is 1.5mm, maximum length is 30 meters. When using
a cable reel, always unwind the cable completely.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........
Volts
n
.......
0
A ........
Amperes
ADDITIONAL SPECIFIC SAFETY RULES
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
a. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
b. Operations such as cutting-off, sander, wire
brush or polisher are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
c. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can
be attached to your power tool, it does not assure safe
operation.
d. The rated speed of the accessory must beat least
equal to the maximum speed marked on the
power tool. Accessories running faster than their
rated speed can break and fly apart.
e. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannon be adequately guarded or controlled.
f.
The arbour size of wheels, flanges,backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
g. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheel for
chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing
an accessory, position yourself and by standers
away from the plane of the rotating accessory and
ENGLISH • 19
Hertz
...... Class II
Watts
....
minutes
.....
Alternating
....
Current
.....
Direct
.../min..
Current
No-Load
Speed
Construction
Earthing
Terminal
Safety Alert
Symbol
Revolutions
or Recipro-
cation per
minute
Tabla de contenido
