Braun KF 7155 Manual Del Usuario página 11

Programming the Coffee Maker
NOTE: The coffee maker features a 60-second
power loss back-up system that remembers all
programmed information, including time of day and
auto on/off times in the event of a tripped breaker,
unit is unplugged, or power failure.
Setting the Time
When the coffee maker is first plugged in or when
power is restored after an interruption, the LED
control panel will start flashing 2:00 AM.
• To set the hour, press the CLOCK button (d) for a
minimum of 3 seconds. The LED control panel will
start flashing.
• Press and hold the SET button (e) to scroll
through the numbers. Release the button once
the desired hour is displayed.
• To set the minutes, press the CLOCK button. The
LED control panel will start flashing.
• Press and hold the SET button to scroll through
the numbers. Release the button once the desired
minutes is displayed.
• Press the CLOCK button again to save the desired
time.
• If during the setting process no button is pressed
for 10 seconds, the time currently set will be
saved.
NOTE: When the number count passes 12, the PM
light will be displayed on the LCD.
Before programming, always switch on the
coffee maker.
Programming and Activating the
AUTO ON Time
• Press the AUTO ON button (b) for a minimum of 3
seconds.
• The hours in the LED panel will start flashing.
• To set the hour, press the CLOCK button (d) for a
minimum of 3 seconds. The LED control panel will
start flashing.
• Press and hold the SET button (e) to scroll
through the numbers. Release the button once
the desired hour is displayed.
• To set the minutes, press the AUTO ON button.
The minutes in the LED control panel will start
flashing.
• Press and hold the SET button to scroll through
the numbers. Release the button once the desired
minutes are displayed.
• Press the AUTO ON button again to save the
desired time.
5713210214_KF 7155/7175_USCA.indd 11 5713210214_KF 7155/7175_USCA.indd 11
• The pre-set auto on time will disappear after 3
seconds and the time of day will show on the LED
control panel.
• If during the setting process no button is pressed
for 10 seconds, the auto on time currently set will
be saved.
This function can only be activated if the auto on
time and the time of the day have been set.
To activate the AUTO ON function:
• Press the AUTO ON button (b). The green LED
above the button will illuminate and the coffee
maker will start to brew at the pre-set auto on
time.
• The pre-set auto on time disappears after 3
seconds.
• When the appliance starts brewing, the green LED
BREW will continually flash and the LED AUTO ON
turns off.
• Press the AUTO ON button (b) again to switch off
the function: the green LED light will disappear.
NOTE: The AUTO ON function remains activated
even when the appliance has been switched off (1).
Setting the Water Hardness Level
Set the water hardness level on the coffee maker to
the water hardness level for your local area.
• Press the CLEAN button (c) for a minimum of 3
seconds.
• The default setting (h3) will start flashing.
• Press the SET button (e) to scroll through the
options (h1 = soft, h2 = normal, h3 = hard) and
select the appropriate water hardness level.
• Press the CLEAN button again to save the
hardness level.
• The pre-set water hardness disappears after 3
seconds and the time of day will show on the LED
control panel.
1 – 4 Cups Setting
• Press the «1-4» button (g). The green LED above
the button will illuminate.
• Press BREW (a) to start brewing.
• The green LED turns off after the brewing cycle is
finished.
Brew Strength Selector
• Press the BOLD button (f) to select brew strength
«bold».
11
29.09.16 08:27 29.09.16 08:27