Tabla de contenido
Idiomas disponibles
Idiomas disponibles
made available to the user.
Only lock and release the door wings when the motor is switched off.
Do not enter within the operating range of the wing.
To dispose of electrical and electronic equipment correctly, users
must take the product to special "recycling centres" provided by
the municipal authorities.
2. Declaration of incorporation of partly com-
pleted machinery
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB, with headquarters in Lodjursgatan 10, SE-261 44 Land-
skrona, Sweden, declares that the automation for Ditec sliding gates NES300EH, NES300EHP,
NES400EH, NES400EHP, NES600EH, NES600EHP, NES1000EHP:
- is designed to be installed on a manual gate to form a machine pursuant to Directive 2006/42/
EC. The manufacturer of the motorised gate must declare conformity with Directive 2006/42/
EC (annex II-A) prior to initial machine start-up;
- conforms to the applicable essential safety requirements indicated in ANNEX I, Chapter 1 of the
Directive 2006/42/EC;
- conforms to the Low Voltage Directive 2006/95/EC;
- conforms to the Electromagnetic Compatibility Directive 2004/108/EC:
- conforms to the R&TTE Directive 1999/5/EC;
- the technical documentation conforms to Annex VII-B of the Directive 2006/42/EC;
- the technical documentation is managed by Marco Pietro Zini with headquarters in Via Mons.
Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY;
- a copy of technical documentation will be provided to national competent authorities, following
a suitably justified request.
Landskrona, 01-07-2014
2.1 Machinery Directive
Pursuant to Machinery Directive (2006/42/EC) the installer who motorises a door or gate has the
same obligations as the manufacturer of machinery and as such must:
- prepare the technical data sheet which must contain the documents indicated in Annex V of the
Machinery Directive;
(The technical data sheet must be kept and placed at the disposal of competent national authori-
ties for at least ten years from the date of manufacture of the motorised door);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery Direc-
tive and deliver it to the customer;
- affix the EC marking on the motorised door or gate, in accordance with point 1.7.3 of Annex I of
the Machinery Directive;
- ensure compliance of the motorised door or gate with safety regulations, by installing the neces-
sary safety devices;
- carry out the safety test
- refer to the installation manual of the CS12E - CS12M control panel for the operating force
adjustments, in compliance with EN12453 and EN12445.
, modifying parameters
31
Matteo Fino
(Chairman)
(Cha
C
C
C
C
C
C h
C
Ch
Ch
Ch
Ch
Ch
C
Ch
C
C
C
C
Ch
C
Ch
C
Ch
C h
C
C
C
C
C
Ch
Ch
C
C
C
C
Ch
C
C
C
C
C h
C
Ch
C h
Ch
C h
Ch
C
C
C
C
Ch
C h
C
Ch
Ch
C
C
C
C
C h
C
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
irm
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
an)
an
and
(if used) from the
menu;
Capítulos
Tabla de contenido
