Tabla de contenido
Push forward until stopping on blade guide, swing cover closed and slightly squeeze to engage magazine
© Stanley Bostitch
bosses. Check positive engagement.
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
DEPTH ADJUSTMENT (All models) (Fig 3)
compliance for the products.
To adjust the tool for different leg lengths, loosen set-screw (A) and turn dial 180° (B) with a screwdriver to the
desired position as noted in the tables at the front of this manual. Tighten set-screw.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
LOADING THE TOOL - DS-3219, DS-3519, DS-3522, DS-SW19, DS-SW22, MS-3219, MS-3519, MS-3522, MS-SW19, MS-SW22
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
A. Pull the pusher to the back of the magazine. (Fig 4)
die CE-Richtlinien für Produkte.
B. Check Staple Leg Length: Adjustment is provided for different staple leg lengths (see section below).
C. Insert 2 sticks of staples into the channel and gently release the pusher against the staples. (Fig 5)
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
CLINCH ADJUSTMENT
D62ADC, RAB-19, RAB-22, DS-3219, DS-3519, DS-3522, DS-SW19, DS-SW22 (Fig 6)
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
MS-3219, MS-3519, MS-3522, MS-SW19, MS-SW22 (Fig7):
produkterne.
Turn special nut (A) through window clockwise to tighten clinch and counter-clockwise to loosen clinch. Use a
tool to fit 1/8" (3mm) hole.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
Depth Adjustment D62ADC, RAB-19, RAB-22, DS-3219, DS-3519, DS-3522, DS-SW19, DS-SW22 (Fig. 8):
Loosen front screw (A) and adjust to desired depth. When top edge of adjustment plate (B) is at highest setting
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
(No. 4), the clinches are at their shallowest penetration. If set at lowest setting (No. 1), the clinchers are at their
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
deepest penetration.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
Note: Tighten screw before firing tool.
conformità CE per i relativi prodotti.
OPERATING THE TOOL (Fig. 9):
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
Grasp handle with one hand. Position on box in line with the desired staple location. There is a small projection
merking for produktet.
on either side of the frame as an aid in locating the position of the staple. Press trigger or pull handle depending
on the model. Move machine to next staple location with or without releasing the trigger.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
Strongest closure requires end staples close to end of box. Check packaging requirements.
Check staple clinching in samples of board being used. Adjustments for depth of penetration and tightness of
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
clinch are easy and instantaneous- full advantage should be taken of them.
conformidad con las normas CE de los productos.
JAM CLEARANCE
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
Jammed Staple Removal - D62ADC, RAB-19, RAB-22 (Fig. 10):
Jams can be cleared by pulling the jam release lever to a 90° position. At this position, hold the coil of staples to
prevent movement and use either a long nose plier or a screwdriver to clear jam. Carefully release lever to
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
prevent staples being trapped between anvil and blade guide.
stanowią deklaracji zgodności CE prezentowanych produktów.
Jammed Staple Removal - DS-3219, DS-3519, DS-3522, DS-SW19, DS-SW22, MS-3219, MS-3519, MS-3522,
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
MS-SW19, MS-SW22 (Fig. 11-13):
stanowią deklaracji zgodności CE prezentowanych produktów.
Remove the remaining stick from the magazine. Pry jam release forward with a screw driver (FIG.11). Remove
magazine (FIG.12). Clear the jam and re-insert the magazine. Pry jam release shut (FIG.13).
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
SECONDARY HANDLE (MS-3219, MS-3519, MS-3522, MS-SW19, MS-SW22)
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
These models come with an additional handle to fit on the top of the tool. To fit, position the handle as shown
a termék CE-megfelelőségét.
(Fig 14) and insert and tighten the 4 screws supplied.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
Tabla de contenido
