Technical Data; Safety Information - FLORABEST 353216 2007 Instrucciones De Montaje

Congratulations!
You have chosen to purchase a
high-quality product. Familiarise
yourself with the product before
using it for the first time.
Read the following as-
sembly instructions and
the safety information
carefully.
Use the product only as described
and only for the given areas of
application. Store these assembly
instructions carefully. When pass-
ing the product on to third parties,
please also hand over all accompa-
nying documents.
Read all safety informa-
tion and instructions. Failure
to adhere to these may result
in severe injury.
Package contents
(Fig. A)
1 x pavilion, disassembled (1–8)
1 x pavilion roof (9)
1 x assembly materials (10–13)
1 x hex key (14)
1 x spanner (15)
16 x ground peg (16)
1 x assembly instructions
1 x quick start guide

Technical data

Dimensions:
approx.
300 x 300 x 260cm (W x D x H)
Date of manufacture
(month/year): 12/2020
Intended use
The product is designed as sun pro-
tection for outdoor use.
It is not intended for permanent out-
door use, as it is only weatherproof
to a limited extent.
The product is not intended for com-
mercial use.
12
GB/IE

Safety information

Life-threatening hazard!
• Never leave children unattended
with the packaging materials.
There is a risk of suffocation.
Risk of injury!
• The product must not be used in
adverse weather conditions such
as strong winds, rain or snow.
• Remove the roof cover of the
product if wind speeds higher than
40km/h are expected (strong
breeze, larger branches and trees
move, and the wind is clearly audi-
ble). The mounted side walls must
also be removed.
• Place the product on an even
surface.
• The product may only be used
under adult supervision and must
not be used as a toy.
• Check the product for damage or
wear before each use.
• Check that all parts have been
properly assembled before each
use. Improper installation can
impair the product's safety and
functionality.
• Keep open flames, barbecues,
and patio heaters outside of and
away from the pavilion! However,
should a pavilion catch fire, leave
it immediately! Extinguish the
blaze with a fire extinguisher or
with water. Immediately alert the
fire department if necessary.
• Individual pavilions must not be
connected or attached to one
another. Individual pavilions must
be at least 3m apart from one
another.
• Any pooled water must be emp-
tied!
Selecting a location
• The product has overall dimen-
sions of 3 x 3m.
• Place the product in a spot least
susceptible to wind.
• The ground should be even and
provide sufficient stability for the
ground pegs.
Assembly
Parts list (Fig. A)
1 – leg, left
2 – leg, right
3 – crossbar
4 – corner roof bar
5 – roof bar
6 – corner connector
7 – T-connector
8 – roof connector
Note! At least 2 people are
required to assemble the
product.
We recommend assembling
the product with 4 people.
Step 1
Screw the legs (1), (2) together at a
right angle, with the screws (13) and
the nuts (10) (Fig. B).
Note: pay attention to the po-
sition of the drill holes on the
sides of the legs. For leg (1),
the drill holes should be on
the inside. For leg (2) the drill
holes should be on the out-
side.
Step 2
Screw the crossbars (3) onto the
legs using the screws (11) (Fig. C).
Note: make sure that the lock-
ing pins of the crossbars are
facing downwards.
Step 3
Screw a corner connector (6)
onto each leg angle with the
screws (12), (13) and the nuts (10)
(Fig. C).
Note: the corner connectors
must be facing slightly up-
wards.
Step 4
Connect the crossbars to the T-con-
nectors (7) (Fig. D).
Note: the locking pins must
click audibly into place.
Step 5
Place the roof connector (8) on the
ground and insert the corner roof
bars (4) and roof bars (5) into the
roof connector (Fig. E).