Honeywell PowPak CLRMJCCO124B Instalación Manual

PowPak | Installation
®
CCO Module
Part of the Energi TriPak Family
®
24 V~ 45 mA
CLRMJCCO124B
NEC
24 V- 35 mA
UL 2043 Plenum Rated
Important Notes:
Please read before installing.
• F or installation by a qualified electrician in accordance with all local and national
electrical codes.
• Note: Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely before
installation.
• Operate between 32 °F (0 °C) and 131 °F (55 °C).
• 0% to 90% humidity, non-condensing.
• For indoor use only.
PowPak
®
CCO Module
Install in center of room to
maximize RF coverage.
Radio Powr Savr
TM
Occupancy Sensor
30 ft (10 m)
Maximum
Pico
®
Wireless Transmitter
40 ft (12 m)
FCC Information:
This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation.
Modifications not expressly approved by Honeywell International, Inc. could void the user's
authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Limited Warranty
Honeywell warrants the products in this document to be free from defects due to
workmanship or materials, under normal use and service, for twelve (12) months from date
of installation.
NEC is a registered trademark of National Fire Protection Association, Quincy, Massachusetts.
Honeywell is a registered trademark of Honeywell International, Inc.
Energi TriPak, Clear Connect, Pico, and PowPak are registered trademarks and Radio Powr Savr
is a trademark of Lutron Electronics Co., Inc.
©2013 Honeywell International, Inc.
Honeywell International, Inc.
1985 Douglas Drive North
® Golden Valley, MN 55422, U.S.A.
Required Components
For each system ensure you have:
At least one PowPak CCO Module.
037248
®
Rev. A
04/2013
CLASS 2
®
CCO
CCO Toggle
Status
LED
Advanced
Operations
Contact
Closure
Output
(CCO)
(Class 2)
PowPak CCO Module
®
Start Here
1 Install PowPak CCO Module
®
When installing a PowPak
Module, use the supplied mounting
screws and wire the module as shown.
All Wireless Suggested Installation Location:
Transmitters
must be Install in center of room.
installed within
This ensures proper RF coverage of area.
30 ft (10 m) of
the PowPak
®
CCO Module. Note: PowPak CCO Module may also be
®
mounted on or inside a junction box.
If installing unit inside a junction box please
see Application Note #423.
For more information:
www.customer.honeywell.com
2 Associate Wireless Transmitters to PowPak
Before beginning this step, make sure that there are no other PowPak
from other systems can be incorrectly associated to this system.
A
Permanently install
3
Wireless Transmitters
Link
Test
Note: Please consult individual
component installation guides
for information.
Need Help? www.customer.honeywell.com or call the Honeywell Technical Support Center at 1.888.235.7316
At least one Wireless Transmitter
+
Radio Powr Savr
TM
Occupancy Sensor
(6 maximum)
Supply Voltage
CCO
®
24 V~ / 24 V-
Wire nut
(2 Supplied)
COM
(Common)
NC
NO
(Normally Closed)
(Normally Open)
CCO Module
®
modules being set up within the same building. It is possible that Wireless Transmitters
®
Hold the CCO Toggle Hold the indicated button on a Wireless Transmitter for
B
button on the PowPak 6 seconds to associate the device.*
®
CCO Module for 6 seconds
Repeat for any additional Wireless Transmitters.
to enter association mode.
Test
* If no g button, hold "Lights Off" button.
Note: The CCO will open and close
Hold the CCO Toggle button on the PowPak
C
once after each step to confirm
successful completion. CCO Module for 6 seconds to save association(s).
Note: Only complete step 4 if using a Daylight Sensor with the CCO Module
4 Daylight Sensor setup
to control a device that is switching a lighting source.
Calibration
A
Turn lights in room on using the
CCO Toggle button on the PowPak
®
CCO Module or an associated Pico .
®
Press & hold "Cal." on the associated
B
Daylight Sensor for 6 seconds.
Exit room for 5 minutes to allow
C
calibration to be completed.
Note: When calibration has completed, all lights
will flash and the system will begin daylighting.
Link Cal.
Test
Pico Radio Powr Savr
®
TM
Wireless Transmitter Daylight Sensor
(9 maximum) (1 maximum)
Note: CCO Module supply wires can be
connected in any polarity.
Mounting screw
(2 Supplied)
To CCO-controlled device.
Note: When wiring CCO output,
use 20 to 16 AWG (0.5 to 1.5 mm )
2
solid or stranded wire.
Link
®
Tuning (Optional)
A
If it is desired to have multiple zones of
lights turn on at different daylight levels
Link Cal.
Test
(using multiple CCO Modules with one
Daylight Sensor) follow the Tuning
procedure described in the Daylight
Sensor installation
(CLLRF2DCRBWH)
instructions.
Use the CCO Toggle button in place of
the Dimmer/Switch tap button referenced
in the document.
CCO Information
• This product features a single contact closure output with both
normally open (NO) and normally closed (NC) dry contacts.
• The CCO incorporates maintained output behavior only.
• The CCO is rated to switch resistive loads at
Switching Resistive
voltages up to 24 V only. To properly control
Voltage Load
R
inductive load types such as relays, solenoids,
0-24 V- 1.0 A
or motors, refer to Application Note #434.
0-24 V~ 0.5 A
Transmitting Device Transmitted Command CCO Default Action
Pico Wireless On NO = Close, NC = Open
®
Transmitter
Off NO = Open, NC = Close
Raise No Action
Lower No Action
Preset NO = Close, NC = Open
Radio Powr Savr Occupied NO = Close, NC = Open
TM
Occupancy Sensor
Unoccupied NO = Open, NC = Close
Radio Powr Savr Occupied No Action
TM
Vacancy Sensor
Unoccupied NO = Open, NC = Close
Radio Powr Savr
Ambient light below target NO = Close, NC = Open
TM
Daylight Sensor level
Ambient light above target NO = Open, NC = Close
level
Unaffected Mode
Unaffected mode allows a system with an Occupancy Sensor
associated to multiple CCO Modules to be set up such that only
selected loads turn on automatically. Other loads will require a
manual turn-on with a Pico Wireless Transmitter. All loads will turn
®
off automatically when the room is vacated.
On a CCO Module, press and hold both the CCO
A
Toggle and Advanced Operations ("ADV") buttons for
6 seconds until the LED begins flashing quickly.
On the associated Occupancy Sensor, press and hold
B
the "Test" button* for 6 seconds until the lens flashes.
Unaffected mode will be exited automatically. This
C
CCO Module will now be unaffected by occupancy
commands. Repeat procedure for any additional
devices.
* If no "Test" button, hold "Lights On" button.
Reset Factory Defaults
Note: In some instances it may be necessary to reset the
PowPak CCO Module back to factory default settings.
®
Triple-tap the Advanced Operations ("ADV") button
A
on the CCO Module and hold until the LED begins to
flash slowly.
Within 3 seconds of flashing, release and triple-tap the
B
button again and the LED will flash rapidly indicating
that the unit has been reset to factory defaults.
Note: Any associations or programming previously set up with the
Cal.
unit will be lost and will need to be re-programmed.
Test
Troubleshooting
www.customer.honeywell.com
CCO- • Ensure power to the PowPak CCO Module is
®
controlled properly applied.
device does • Ensure the CCO-controlled device has been
not respond properly wired to the PowPak CCO Module.
®
to Wireless
• Ensure Wireless Transmitter is properly
Transmitter(s) associated to PowPak CCO Module.
®
• Ensure Wireless Transmitter's battery is installed
correctly.
Wireless • The maximum number of Wireless Transmitters
Transmitter(s)
have been associated to the PowPak CCO
®
cannot be Module. To remove a previously set up Wireless
associated to Transmitter, tap the button used for association
PowPak on the Wireless Transmitter three times, on the
®
CCO Module third tap hold for three seconds and then tap
three more times.