Heath Zenith Secure Home DualBrite SH-5316 Manual De Instrucciones página 3

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

TEST AND ADJUSTMENT
❒ Turn on the circuit breaker and light switch.
NOTE: Sensor has a 1
before it will detect motion. When first turned
on, wait 1
/
minutes.
1
2
❒ Turn the RANGE control to the medium position
(halfway between MIN and MAX),D
and the ON-TIME control to the TEST position.
MAX
ON-TIME
MIN
TEST 1 5 20
RANGE
MINUTES
Bottom of Sensor
Avoid aiming the sensor at:
• Objects that change temperature rapidly, such as
heating vents and air conditioners. These heat
sources could cause false triggering.
• Areas where pets or traffic may trigger the control.
• Nearby large, light-colored objects reflecting light
may trigger the shut-off feature. Do not point other
lights at the sensor.
15 ft.
(4.6 m)
70 ft.
D
Z
ual
one
(21 m) (30.5 m)
Maximum Range
NOTE: If fixture is mounted higher than 8 ft. (2.4 m), aiming
the sensor down will reduce coverage distance.
The detector is less sensitive to motion directly towards it.
Motion
D
Z
ual
one
Least Sensitive
598-1153-02
/
minute warm up period
1
2
B
®
ual
rite
DUAL BRITE™
OFF 3 6 DUSK TO
HOUR
DAWN
240°
D
Z
ual
one
100 ft.
Boosted
Maximum
Coverage Angle
Motion
D
Z
ual
one
Sensor
Most Sensitive
❒ Loosen the clamp screw
in the sensor ball joint and
gently rotate the sensor.
❒ Walk through the coverage
area noting where you are
when the lights turn on (also,
the LED will flash several
times when motion is detect-
ed). Move the sensor head up,
OFF,
down, or sideways to change
the coverage area. Keep the
sensor at least 1" (25 mm)
away from the bulbs.
❒ Adjust t he R ANGE a s n eeded.
RANGE set too high may
increase false triggering.
❒ Secure the sensor head's
aim by tightening the clamp
screw. Do not overtighten the
screw.
❒ Set the amount of TIME you want the lights to stay
on after motion is detected (1, 5, or 20 minutes).
❒ Set the D
ual
after dusk you want the lights on at low level (Off,
3, 6 Hrs., Dusk-to-Dawn).
WARNING - Risk of fire. Do not aim the bulbs
at a combustible surface within 3 ft. (1 m).
NOTE: D
Z
ual
one
was added as an option to select Heath
sensing products. This feature adds a zone of detec-
tion under the motion sensor. D
no additional adjustment and operates in conjuction
with the forward-looking sensor.
SPECIFICATIONS
Horizontal Range . . . . Up to 70 ft. (21 m); 100 ft.
Vertical Range . . . . . . Up to 15 ft. (4.6 m)
Sensing Angle . . . . . . Up to 240° horizontal. Up to 80°
Electrical Load . . . . . . Up to 500 Watts Maximum In-
Power Requirements . 120 VAC, 60 Hz
Operating Modes . . . . TEST, AUTO and MANUAL
Time Delay . . . . . . . . 1, 5, 20 minutes
D
B
Timer . . . . Off, 3, 6 hours, Dusk-to-Dawn
®
ual
rite
HeathCo LLC reserves the right to discontinue prod-
ucts and to change specifications at any time without
incurring any obligation to incorporate new features in
products previously sold.
3
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
B
switch to the amount of time
®
rite
™ is a new zone of detection which
/Zenith motion
®
Z
ual
one
(30.5 m) with Range Boost.
[var ies with surrounding
temperature]
Vertical
candescent
MODE
Clamp
Screw
Ball
Joint
™ requires
Tabla de contenido
loading

Tabla de contenido