Tabla de contenido
Operating Instructions
General Safety Information
(Cont.)
The regulated pressure must not
exceed 100 psi. If the regulator fails,
the pressure delivered to the tool
must not exceed 200 psi. The tool
could explode which will cause
death or serious personal injury.
● Never use gasoline
or other flammable
liquids to clean the
tool. Never use the
tool in the presence
of flammable liquids or gases.
Vapors could ignite by a spark and
cause an explosion which will result
in death or serious personal injury.
● Always remain in
a firmly balanced
position when
using or handling
the tool.
● Do not remove,
tamper with, or
otherwise cause
the Work Contact
Element (WCE) or
trigger to become
inoperable. Do
not operate any tool which has been
modified in a like fashion. Death or
serious personal injury could result.
● Do not touch the
trigger unless dri-
ving fasteners.
CAMPBELL
CAMPBELL
HAUSFELD
HAUSFELD
PROFESSIONAL
PROFESSIONAL
Never attach air
line to tool or
carry tool while
touching the trig-
ger. The tool could eject a fastener
which will result in death or serious
personal injury.
Nailer Components And Specifications
• REQUIRES: .80 SCFM with 10
nails per minute @ 90 psi
• AIR INLET: 1/4" NPT
• NAIL SIZE RANGE: 3/8" to 1-1/4"
• MAGAZINE CAPACITY:
100 Nails per load, 18 gauge
• WEIGHT: 2 lbs., 9 oz.
• LENGTH: 9"
• HEIGHT: 7"
• MAXIMUM PRESSURE: 100 psi
• PRESSURE RANGE: 50 - 100 psi
www.chpower.com
Warning indicates
WARNING
!
a potentially
hazardous situation which, if not avoid-
ed, COULD result in death or
serious injury.
● Always discon-
nect the tool
from the power
source when
unattended,
performing any
maintenance or
repair, clearing a jam, or moving the
tool to a new location. Always
reconnect the air line BEFORE load-
ing any fasteners. Do not load the
tool with fasteners when either the
trigger is depressed or the Work
Contact Element (WCE) is engaged.
The tool could eject a fastener caus-
ing death or serious personal injury.
● Always fit tool
with a fitting or
hose coupling
on or near the
tool in such a
manner that all
compressed air in the tool is dis-
charged at the time the fitting or
hose coupling is disconnected. Do
not use a check valve or any other fit-
ting which allows air to remain in the
tool. Death or serious personal injury
could occur.
● Never place hands or
any other body parts
in the fastener dis-
charge area of the
tool. The tool might
eject a fastener and
could result in death
or serious personal injury.
Cap Exhaust
Work Contact
Element (WCE)
2
● Never carry the
tool by the air
hose or pull the
hose to move the
tool or a com-
pressor. Keep
hoses away from
heat, oil and sharp edges. Replace
any hose that is damaged, weak or
worn. Personal injury or tool dam-
age could occur.
● Always assume the tool contains fas-
teners. Respect the tool as a work-
ing implement; no horseplay.
Always keep others at a safe dis-
tance from the work area in case of
accidental discharge of fasteners. Do
not point the tool toward yourself
or anyone whether it contains fas-
teners or not. Accidental triggering
of the tool could result in death or
serious personal injury.
● Do not drive a
fastener on top
of other fasten-
ers. The fastener
could glance and
cause death or a
serious puncture
wound.
● Do not operate
or allow any-
one else to
operate the
tool if any
warnings or
warning labels
are not legible. Warnings or warning
labels are located on the tool maga-
zine and body.
● Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam
Warning Labels
Trigger
Nail Loading Area
Nail Discharge Area
Model NB003004
WARNING
!
Latch
Magazine
Capítulos
Tabla de contenido
