Setting The Clock; Timer Setting; Adjusting Parameters - Italiana Camini MAREA Instalación Uso Y Mantenimiento

Setting the clock

Press the 'Menu' key for 2 seconds to access the Clock Menu and set the clock parameters in the control board.
By pressing the 'Menu' key again, the following parameters will appear in sequence and each can be adjusted:
Day, month, year, hour, minute, day of week.
When 'Save??' appears on the display you can verify that the settings have been entered correctly before confirming. Pressing
the 'Menu' key saves the information and 'Save OK' then appears on the display.

Timer setting

Press the 'Menu' key for two seconds to access the time setting function and press the + key to access the timer settings
function: "Program on/off" appears on the display.
A maximum of three timer programs can be set for each day of the week.
When "timer On/off" appears on the display, press the 'Menu' key and one of the following messages will appear:
NO PROGRAM (no timer program is set)
DAILY PROGRAM (one program is set for every day)
WEEKLY PROGRAM (a program is set for each day of the week)
Press the + and – keys to go from one program to another.
Press the 'Menu' key to confirm the "DAILY PROGRAM" option and access the number of programs (ignition/shutdown) to
be set in a day.
In the "DAILY PROGRAM" option the timer program(s) set will be the same for each day of the week.
The following will be displayed if the + key is pressed:
- No program
- 1st program (one ignition and one shutdown a day), 2nd program (same as before), 3rd program (same as before)
Use the key to view them in reverse order.
If the 1st program is selected, the ignition time is displayed.
The following appears on the display: 1 ON hour 10:30. The hour is changed with the +/- key and the setting is confirmed by
pressing the 'Menu' key.
The following appears on the display: 1 ON minutes 10:30. The minutes are changed with the +/- key and the setting is
confirmed by pressing the 'Menu' key.
The shutdown time and any subsequent ignition/shutdown programs are set in the same way.
To save the settings, press the 'Menu' key when 'Save??' appears on the display.
In the "WEEKLY PROGRAM" option you must select the day you wish to apply the program to:
1 Mo; 2 Tu; 3 We; 4 Th; 5 Fr; 6 Sa; 7 Su
Once the day is set, by scrolling with the + and – keys and confirming with the 'Menu' key, you can continue setting the timer
programs in the same way as for "DAILY PROGRAM", selecting one timer program or more for any day of the week.
If you make a mistake at any point you can exit without saving by pressing the 0/1 key and 'Saved' will appear on the display.
Functions controlled solely from the Control Panel
Adjusting the pellet load
The pellet load must be adjusted only if the DEALER has DISABLED the 'self-adjusting combustion'.
Press the 'Menu' key for two seconds and scroll through the titles on the display with the +/- keys until you come to "adj.
pellets".
Press the 'Menu' key to enter this function whereby you can adjust the pellet load: by decreasing the set value you will
decrease the pellet load, by increasing the set value you will increase the pellet load. This function may be useful when the
type of pellets has been changed and therefore, it is necessary for the pellet load to be adjusted.
If this adjustment does not suffice please contact the DEALER to set the new operating parameters.
Cold test (I/O TEST)
The components can be tested through this menu, which can only be accessed when the stove is in standby mode.
Only authorised DEALERS can access this and in fact it is code protected.

Adjusting parameters

Press the 'Menu' key for two seconds and scroll through the titles with the +/- key until you come to the
"SETUP" menu.
Through this option you can adjust the main parameters that control the stove's operation.
Only authorised DEALERS can access this and in fact it is code protected.
- 21
-