Description; Transport And Storage; Maintenance; Warranty - VALPES VT+ Serie Manual De Instalación Y Funcionamiento

DESCRIPTION

These electric actuators have been designed to perform the control of a valve with 90° rotation. Please consult us for any
different application. We cannot be held responsible if the mentioned actuators are used for any other purpose.

TRANSPORT AND STORAGE

 The forwarding agents being held as responsible for damages and delays of the delivered goods, the consignees are
obliged to express if applicable their reserves, prior to accept the goods. The goods delivered directly ex works are
subject to the same conditions.
 The transport to the place of destination is carried out by using rigid packing material.
 The products must be stored in clean, dry, and ventilated places, preferably on appropriate palettes or shelves. Actu-
ators should not be stored upside down.

MAINTENANCE

 Maintenance is ensured by our factory. If the supplied product does not work, please check the wiring according to
the electric diagram as well as the power supply of the electric actuator in question.
 For any question, please contact our after-sales service.
 To clean the outside of the actuator, use a lint and soapy water. DO NOT USE ANY CLEANING PRODUCT WITH
SOLVENT OR ALCOHOL.

WARRANTY

 100% of the actuators are fully tested and pre-set in our factory.
 These products have a 3-year warranty from the delivery date or 50,000 operating cycles against all types of manu-
facturing and material faults (operating time and model class according to standard IEC34).
 This warranty will only be valid if the unit has not been disassembled or self-repaired during its service life. The war-
ranty neither applies for wear or damages caused by chocks or faulty operations nor by the use of the unit following
conditions not in accordance nor with its nominal characteristics. The warranty is strictly limited to the replacement of
original parts found defective when checked by our member staff. The cost of shipping to our premises, the return of
devices to the customer as well as the repair cost will be chargeable. We will not take responsibility for any direct or
indirect accidents/risks originated by a failure of our products. The warranty does not cover the consequences of
breakdown and excludes any payments for indemnities. The accessories and adaptations are excluded from the war-
ranty. In the event that a customer has not proceeded to payments within the agreed period, our warranty will be sus-
pended until the delayed payments have been received and with the consequences that this suspension will not pro-
long the warranty period in any case.

RETURN OF GOODS

 When the actuator receives his actuator, he must check its conformity according to its definition.
 The acceptance of the goods by the purchaser disclaims the supplier of all responsibility if the purchaser discovers
any non-conformity after the date of acceptance. In such case, the repair cost will be borne by the purchaser who will
also exclusively bear all financial consequences of any resulting damages. Returned goods will only be accepted if our
prior agreement has been given to this procedure : the goods must be sent free of all cost and being shipped solely
and in their original packing. The returned goods will be credited to the purchaser with a reduction of 40% on the
unit's price charged in accordance with the original invoice of the returned goods.

SAFETY INSTRUCTIONS

 The electric power supply must be switched-off before any intervention on the electric actuator (i.e. prior demounting
its cover or manipulating the manual override knob).
 Any intervention must only be carried out by a qualified electrician or persons instructed in accordance with the regu-
lations of electric engineering, safety, and all other applicable directives.
 Strictly observe the wiring and operation instructions as described in the manual: otherwise, the proper working of the
actuator can not be guaranteed anymore. Verify that the indications given on the identification label of the actuator
fully correspond to the characteristics of the electric supply.
 Any other use than that described by the manufacturer jeopardizes the protection provided by this apparatus.
MOUNTING INSTRUCTIONS
 Do not mount the actuator less than 30 cm from an electromagnetic disturbance source.
 Do not position the equipment so that it is difficult to operate the disconnecting device.
 Respect all safety rules during fitting, dismantling and porting of this apparatus.
DSBA3600 • Rév. 08/03/2018
(To be read prior to the installation of the product
(To be read prior to the installation of the product
ENGLISH
UK
)
)
19