Stanley STDR5510 Manual De Instrucciones página 12

12 • ENGLISH
power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tools, accessories and tool bits, etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY
the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
ADDITIONAL POWER TOOL
SAFETY WARNINGS
Warning! Drill safety warnings.
f Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
f Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
f Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed metal
parts of the power tool "live" and shock the operator.
f Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
f This tool is not intended for use by persons(including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concern ing use of the appliance by a person responsible
for their safety. Children should be supervised to
ensure that they do not play with the appliance.
f The intended use is described in this instruction
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recom- mended in this instruction manual
may present a risk of personal injury and/or damage
to property.
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/Reverse slider
4. Chuck
5. Sleeve
6. Bit Shaft
7. Chuck key
8. Hole
9. Speed dial
Construction
ASSEMBLY
Earthing
Terminal
Warning! Before assembly, make sure that the tool is
Safety Alert
switched off and unplugged.
Symbol
Revolutions
Keyed chuck (Fig. B)
or Recipro-
cation per
f Open the chuck by turning the sleeve (5) counterclockwise.
minute
f Insert the bit shaft (6) into the chuck.
f Insert the chuck key (7) into each hole (8) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. C)
f Open the chuck as far as possible.
f Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f Tighten an Allen key into the chuck and strike it with