Sammic CK-35V/38V Instrucciones página 14

EN
Two lines are displayed in the centre of the screen (1) when the machine is switched on. Icon number 7 (representing a cutting disk) is displayed if the
"Vegetable Cutter" accessory is mounted and Icon number 5 (representing a rotor) is displayed if the "Cutter" is mounted. This shows that the control
panel has identified each attachment. The speed level and the associated RPM are also displayed.
Speed levels from 1 to 10 can be selected in Cutter mode and from 1 to 5 in "Vegetable Cutter" mode.
- Time control: Only available in "Cutter" mode. The countdown time and automatic shut-down can also be set.
- The appropriate informative text will appear on the screen if "Start" is pressed while any of the safety devices out of position.
START-UP GENERAL OPERATION
AND
"Vegetable Cutter" operating mode (CK-35V/38V, CA-3V/8V).
With the machine disconnected from the mains:
- With the bayonet mechanism (Y) open (AA), place the "Vegetable Cutter" accessory on the motor block so that the three lugs are inserted into the holes
of the quick-lock mechanism. Close (Z) the bayonet mechanism (Y) to lock the accessory on the motor block.
- The hinged cover (J) on the CK-35V/38V and CK-45V/48V must be fitted as indicated in the drawings and secured with the pin (O).
- The plunger (M) on the CK-35V/38V must be placed as indicated in the drawings and secured with the pin (N).
- If you wish to use the tube head with the CK-35V/38V and CK-45V/48V, it must be placed as indicated in the drawings and secured with the pin (O).
Fitting the disks (A) and grids (B)
- Open the lock (I) and open the hinged lid (J).
- Place the ejector (C) in its housing in the
dive shaft.
- The grid (B) is inserted into the cavity in the lower cover (D) when the process so requires.
- Fit a disk (A) on the drive shaft. To do so, insert the disk (A) onto the drive shaft and turn it clockwise until it engages with the shaft.
- On the CK-45V/48V and CA-4V, thread the bit (Q) or the mixer (R) - depending on the product to be cut - onto the drive shaft.
- Close (J) and lock (I) the hinged cover.
Start the machine and Icon number 7 (represented by a cutting disk), the speed level and its associated RPM will be displayed on the screen. The speed
can be adjusted with the motor running or stopped.
Pressing "Run" (7) with the hinged lid (J) closed and the plunger (M) down will start the motor. Icon 7 will begin to rotate, indicating that the motor is
engaged.
The "Pause" icon will be displayed if "Start" (7) is pressed with the motor stopped, the hinged lid (J) closed and the plunger (M) up, indicating that the
plunger must be lowered. The motor will start up when the plunger (M) is lowered.
The motor will stop if the plunger (M) is raised.
The motor re-starts automatically when the plunger (M) is lowered. The "Start" button (7) must be pressed again to start the motor if the plunger (M) is
kept in the raised position for more than 30 seconds.
The motor will stop if the hinged lid (J) is opened. The "Start" button (7) must be pressed again to start the machine once the hinged lid (J) has been
closed.
The machine will stop automatically after
30 minutes if it is left running with the plunger (M) in the lowered position.
An indicative text will appear on the screen if any of the safety devices is out position.
FORCE CONTROL function
- With the motor running, ring 3 on the screen indicates load under which it is working. When the indicator approaches the red zone, it means that the
motor is nearing overload. This level varies depending on the features of the product being processed and the force exerted by the plunger.
- An acoustic signal to warn the user that a certain level of force has been reached can be configured. This is useful to ensure that constant force is applied
to obtain uniform cutting.
- Increase the load on the plunger until the acoustic signal sounds, indicating that the desired level of force has been reached. Maintain this load without
increasing the force to obtain uniform cutting throughout the process.
- To set the acoustic signal, hold down the reverse rotation button (C) for 3 seconds to access the menu with which to set the load level at which the
acoustic signal will sound. Press the same key (D) again to exit the menu.
Operation with standard hopper (J) and plunger (M) CK-35V/38V and CA-3V.
- The mallet (L) must be housed and locked in its hole. Rotate it anti-clockwise to do so.
- Start the machine.
- Raise the plunger (M). The motor will stop.
- Insert the products into the standard hopper (J).
- The motor will start and the cutting process begin once the user begins to press down on the plunger (M). Feed the product by gently lowering the
plunger (M). Repeat the process as many times as required.
- Press "Stop" (A) once production has finished.
Operation with the standard intake hopper (K) and plunger (M). CK-45V/48V and CA-4V.
- The mallet (L) must be housed and locked in its hole. Rotate it anti-clockwise to do so.
- Start the machine.
-14-