Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Bulkhead connector outputs - Terminals for the included mating connector can be acquired at a GM dealership in the Delphi
Terminal Service kit. Terminals are Delphi part number 15326269 (GM part number 19167018), and wire seals are Delphi part
number 15366021 (white seal).
At many dealerships these can be found in the Parts Department.
•
GMLAN Communication Link (TAN/BLACK STRIPE [+], TAN [-]) –
This provides the GMLAN communication messages containing engine operating parameters for potential use in future add
on modules – any current integration of this is left to the user. Can be used with a LAN dash or an electronic dash readout
display.
•
Tachometer Signal (WHITE) – This is a 2 pulse/rev output (see features above).
•
Vehicle Speed (BROWN) – This is a non scaled output for use with auto-scaling speedometers and will not function unless
a vehicle speed sensor (VSS) is connected to the ECM through the VSS wire in the harness.
•
MAP (LT GREEN) – This is an output for use in gauges or for load indication in transmission controllers (any connection must
be to high-impedance device). The output is a 0-5 Volt signal ranging from 10 – 105 KPa (1.5 – 15.2 psia). Use the ground
wire in the bulkhead connector as the low reference (ground).
•
Oil pressure Sensor (TAN/WHITE STRIPE) – This is the output from the oil pressure sensor which can be used for monitoring
(Pressure (psig) = [32*Sensor Voltage]-16). Use the ground wire in the bulkhead connector as the low reference (ground).
PSI = (32*voltage-16)
Volts
0.5
1.0
2.0
3.0
4.0
5.0
Throttle Position (PURPLE) – This is an output for use in gauges or for load indication in transmission controllers (any connection
must be to a high-impedance device). The output is a 0.5 – 4.5 volt signal ranging from 0 – 100 %. Use the ground wire in the
bulkhead connector as the low reference (ground).
•
10A Fused 12V Power (ORANGE) – This is a power output supply and is always enabled.
•
15A Fused 12V Ignition Power (PINK) – This is a power output supply and is enabled only when the ignition is on.
•
Ground (BLACK) – This is used as the low reference (ground) for completion of the MAP, TPS, and oil pressure output circuits.
It can also be used for modules connected to either of the fused 12V outputs.
Terminals for the included mating connector can be acquired at a GM dealership in the Delphi Terminal Service kit (J38-125) in
tray 8, position 9. At most dealerships this can be found at the Service Desk.
NOTE: If you are using GMPP Supermatic Transmission Controller Kit # 19212657 the Tachometer Signal (WHITE) and Throttle
Position (PURPLE) are required to be connected. If you are using GMPP Supermatic Connect and Cruise kit #19257634 or
19257661 the Bulk Head Connector must be plugged into the GMPP Supermatic Connect and Cruise harness. For the Connect
and Cruise kit the tachometer signal and the throttle position signal are received through the bulk head connector.
Start-up and Break-in Procedures
Safety first. If the vehicle is on the ground, be sure the emergency brake is set, the wheels are chocked and the car cannot fall
into gear. Verify everything is installed properly and nothing was missed.
1. Oil & Fluid Fill: This engine assembly may need to be filled with oil or have oil added. After installing the engine, ensure
the crankcase has been filled with the appropriate motor oil to the recommended oil fill level on the dipstick. The 6.2L LS9
Crate Engine requires a special oil meeting GM Standard GM4718M (this will be specified on the oil label). Mobil 1 is one
such recommended oil. Other oils meeting this standard may be identified as synthetic. However, not all synthetic oils will
meet this GM standard. Look for and use only oil that meets GM Standard GM4718M. Also check and fill as required any
other necessary fluids such as coolant, power steering fluid, etc.
LS9 Crate Engine Control System
TITLE
ALL INFORMATION WITHIN ABOVE BORDER TO BE PRINTED EXACTLY AS SHOWN ON 8 1/2 x 11
WHITE 16 POUND BOND PAPER. PRINT ON BOTH SIDES, EXCLUDING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE WITH GM SPECIFICATIONS.
PSI
0.0
16.0
48.0
80.0
112.0
144.0
IR 27MY16
19299465
PART NO.
DATE
8
SHEET
REVISION
40
OF
AUTH
Tabla de contenido
