Wiring Diagrams; General Information; Technical Specifications - Comelit 3188A Manual Tecnico

EN Warning
• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force.
• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for modifi cations
made by third parties for any reason or purpose, and for the use of non-original accessories and materials.
• All the products comply with the requirements of the 2006/95/CE directives (which replace directive 73/23/CEE and subsequent amendments), as certifi ed by the CE mark on
the products.
• Do not route riser wires in proximity to power supply cables (230/400V).
• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised electricians.
• Cut off the power supply before carrying out any maintenance work.

WIRING DIAGRAMS

• CA/BI "VANDALCODE" electronic key system................................................................................................................................................................16
• VCC/01B/PCI "VANDALCODE" electronic key system in traditional cabling video door entry system........................................................................................17
• C5/AADI "VANDALCODE" electronic key system variant in traditionally wired door-entry phone systems........................................................................18
• SB2/ABDI "VANDALCODE" electronic key system variant in SBC system with Powercom keystone jacks Art. 1602, Art. 4660, Art. 4660C........................18
• SB2V/042SMCCA "VANDALCODE" electronic key system in video entry phone systems with SBC wiring and Ikall AV keystone jacks Art. 4680C.........................19
• SBC_016ECA "VANDALCODE" electronic key system in door-entry phone system with Simplebus wiring and Ikall audio keystone jack Art. 1622....................20
• SB2/ABVIC "VANDALCODE" electronic key system variant in SBC system with IKall keystone jacks and additional buttons Art. 3064C .............................20

GENERAL INFORMATION

Art. 3188A for mounting in Vandalcom modular keypads for mixed access
control - entry panel - video entry panel installations or stand-alone applications.

TECHNICAL SPECIFICATIONS

• 403 total available codes:
- one supercode;
- 400 relay codes. The available codes can be distributed in any way
between relay 1 and relay 2. Example: 245 different codes for relay 1, and
55 different codes for relay 2;
- one anti-coercion code.
• Available outputs:
2 on independent relays, 2 open collector
• Operation of the relay outputs: keypad programmable, mono- or bistable.
• Monostable mode: pulse programmable from 1" to 99" approx.
• Supercode: 1 to 8 repeatable digits.
• Relay codes: 1 to 8 repeatable digits.
• Anti-coercion code: 1 digit.
• Remote key input.
• Programming input.
• Single-key operation mode input (timetable programmer).
• 3 LEDs, depending on model:
- 2 to indicate relay closure and 1 to indicate programming mode.
• Outputs (NO-NC), potential free.
• Contact capacity: 24V AC/DC MAX.
• Service output: max 500 mA.
• Power supply: 12V AC/DC stand-alone.
• Power Consumption: 250 mA 12V AC with 2 relays active.
• Operating temperature: -10°C to +50°C.
PROGRAMMING AND OPERATION
There is a timeout for programming procedures after which the operation is
cancelled (around 40" between successive keystrokes); we recommend
familiarising yourself with the procedure before starting it.
1) Entering the supercode
Programming the supercode is the fi rst operation, because all subsequent
steps depend on it.
We recommend using a short, easy to remember supercode, or noting it down
on a sheet of paper.
Entering the supercode
1)Power up the key which has been cabled but is still open.
2)Insert a jumper between PGM and the negative (- or ck2 ).
3) Check that the red LED has lit up.
4) Enter the supercode (1 to 8 digits).
5) Press "E" to store the code.
6) Wait for 10 seconds or for the confi rm tone to sound.
7)Remove the jumper.
Example:
to enter supercode 12345, proceed as follows:
-power up;
-fit the jumper;
-enter in sequence 1 2 3 4 5 E;
-wait for 10 seconds or for the confirm tone to sound; remove the jumper.
• If you make an error in entering the code, press the "key"
several times to cancel the operation.
• You must always enter "E" at the end of the operation, whether during
programming or normal use.
• Modifying or changing the supercode resets all other programmed
settings (including relay codes).
• The supercode cannot be reset to a default value, but only replaced.
4
2) Relay codes: fi rst programming
To program the relay codes, you must fi rst know the supercode. The red LED on
the keypad stays on during the programming procedure.
In case of error, it fl ashes briefl y and then turns off, after which you must start
again from the beginning of the procedure.
Relay codes: fi rst programming procedure
1) Enter "0" and "E" (start programming procedure code).
2) Check that the red LED has lit up.
3) Enter the supercode (entered in point 1) followed by "E".
4) Enter the relay ID number (1 or 2) followed by "E".
5) Enter the operating mode (see point 5), then "E".
6) Enter the new code followed by "E".
7) The LED should now turn off.
Example:
To enter code 55127 for relay 1 in bistable mode (on/off), make the following
keystrokes:
0 E start procedure
12345 E supercode
1 E relay 1 ID
O E bistable operating mode
55127 E new code
3) Using relay codes
After programming is completed, you can activate relay 1 by simply entering:
55127 E. In this example, the operating mode has been set to 0, in other words,
bistable (on/off).
To activate monostable operation, refer to point 5.
• Up to 400 codes can be set relay 1 or relay 2. If you attempt to enter a
code which has already been stored, an error is indicated.
4) Cancelling relay codes
The following procedure cancels stored codes from memory:
1) Enter "0" and "E" (start programming procedure code).
2) Check that the red LED has lit up.
3) Enter the supercode (entered in point 1) followed by "E".
4) Enter "0" (cancel code) followed by "E".
5) Enter the code to be cancelled, followed by "E".
6) The LED should now turn off.
Example:
to cancel code 55127, enter in sequence:
0 E start procedure
12345 E supercode
0 E cancel
55127 E code to be cancelled
5) Bistable/Monostable operation
The relays can be programmed to operate in bistable (on/off) or monostable
(timed) modes (the period of activation can also be set in the latter case).
Bistable mode:
entering the value "0" sets the relay to activate when the code is fi rst entered,
then de-activate when it is next entered.
button
Monostable mode:
entering a value in the range 1 to 99 sets the relay to activate when the code is
entered and de-activate automatically once the specifi ed period of time (1 to 99
seconds) has expired.