Especificaciones Técnicas - Aim TTi MX100Q Manual De Instrucciones

Tabla de contenido
14 Especificaciones técnicas
En el rango de temperatura de 5 °C a 40 °C se aplican las especificaciones generales. En el rango de
temperatura de 18 °C a 28 °C, tras 15 minutos de calentamiento sin carga y calibración a 23 °C, se
aplican las especificaciones de precisión. Las especificaciones típicas vienen determinadas por el
diseño y no están garantizadas.
OUTPUT SPECIFICATIONS (Each Output)
Voltage/Current
Ranges:
Output Power:
Voltage Setting:
Current Setting:
Operating Mode:
Output Switch:
Multi-On/Multi-Off
Action:
Output Terminals:
Ripple & Noise
(20MHz bandwidth):
Load Regulation:
Line Regulation:
Transient Response:
Temp. Coefficient:
O/P1: 0V to 35V/0.1mA to 3A or 0V to16V/0.1mA to 6A
or 0V to 35V/0.1mA to 6A with O/Ps disabled.
O/P2: 0V to 35V/0.1mA to 3A or 0V to16V/0.1mA to 6A
or 0V to 35V/0.1mA to 6A with O/Ps disabled.
O/P3: 0V to 35V/0.1mA to 3A, 0V to 70V/0.1mA to 1.5A
or 0V to 70V/0.1mA to 3A with O/Ps disabled
O/P4: 0V to 35V/0.1mA to 3A, 0V to 70V/0.1mA to 1.5A
or 0V to 70V/0.1mA to 3A with O/Ps disabled
Up to 420W total output power
Resolution: 1mV O/P1 ,O/P2; O/P3 & O/P4(35V) 10mV O/P3 &
OP4(70V)
Accuracy: O/P1,OP2,OP3 & O/P4(35V): ± (0.05% of setting + 3mV),
OP3 & O/P4(70V): ± (0.1% of setting + 10mV)
Resolution: 0.1mA
Accuracy: ± (0·3% + 3mA) to 3A, ± (0·5% + 3mA) to 6A
Constant voltage or constant current with automatic cross-over.
CV or CC mode indication in display.
Independent electronic switching with ON indication. In addition, Multi-On
and Multi-Off keys permit the outputs to be switched on/off synchronously.
Individually settable delay between pressing of the Multi-On or Multi-Off key
and the turning on or off of the respective output. Delays settable between
10ms and 20 seconds. Separate delays for On and Off can be set.
Outputs can also be omitted from Multi-On or Multi-Off control.
Universal 4mm safety binding posts on 19mm (0·75") spacing for Output;
screwless terminals for Sense.
MX100QP also has duplicate power and sense terminals at rear.
Outputs 1 & 2 loaded at 16V/6A, Outputs 3 & 4 loaded at 35V/3A, CV mode:
All Outputs typically <0.5mVrms, <5mV pk-pk; 1mVrms max.
Rear terminals: 10mV pk-pk max. 1.5mVrms max.
O/P3 & O/P4 on 70V/3A range:
Typically <1mVrms, <10mV pk-pk; 1.5mVrms max.
Rear terminals: 15mV pk-pk max.
For any load change, measured at the output terminals, using remote sense:
Constant voltage: <0.01% ± 5mV
Constant current: < 0.01% ±0.5mA
Change in output for a 10% line change:
Constant voltage: <0.01% ± 5mV
Constant current: < 0.01% ± 250uA
To within 50mV of set level for a 5% to 95% load change:
Front terminals: <150us.
Rear terminals: <175us
Typically <100ppm/°C
Página 43
<500us (Outputs 1 & 2: 35V/6A range).
Tabla de contenido
loading

Este manual también es adecuado para:

Mx100qp

Tabla de contenido