Setting The Flight Phase Transition Time; Checking / Changing The Properties Of The Current Model Memory; What Is Displayed; What Can Be Changed - Multiplex ROYALpro 7 Manual De Instrucciones

19.4.4.

Setting the flight phase transition time

In the bottom line of the menu you can set the tran-
sition time ( Time ) for moving between flight phases:
OFF 1sec
!
Exception: auto-rotation
Switching into the AUTOROT flight phase always
occurs without any delay!
Checking / changing the Proper-
19.5.
ties of the current model memory
Menu I Memory , Properties :
19.5.1.

What is displayed?

¦Properties
¨Exit
Template
Mode
Assignment
Name
Template (cannot be changed!):
If you have used an "unsuitable" Template when
setting up a new model, you must erase the model
and create it anew.
19.5.2.

What can be changed?

Stick Mode s 1 to 4 are available:
The double arrows indicate the sticks which are
used to control elevator ( è ) and rudder ( é )
( 14.3.).
Assignment :
When you set up a new model you select one list
from the five assignment lists. Your selection can
be changed subsequently in this menu
( 14.3.).
Model Name :
The model name can be entered using up to six-
teen characters
( 11.1.1.).

Setting up a New model

19.6.
Menu: I Memory , New model :
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
a. Memory nr.
For a new model the software uses the transmit-
ter's first available vacant memory. It is not pos-
sible to choose the memory.
If you wish to store the new model in a different
memory, you can subsequently copy the new
model into a different memory location (
If all the memories are occupied, the screen shows:
Memory nr.
2sec 4sec
Template used to create
the model
GLIDER
Selected stick mode
4: èé
(elevator / rudder right)
GLIDER
Cularis
Selected assignment
Model name
3 a.
GLIDER b.
MPX-UNI c.
4: è é d.
GLIDER e.
f.
19.2.).
-1
If you still attempt to set up the new model by pres-
sing OK , you will see the following on-screen warning:
No memory free
Press ENTER
If you see this message, please leave the menu. You
cannot store a new model until you have erased a
model which you no longer need (
b. Template
Under Template you determine the basic model
type which applies to the new model you wish to
set up. Your fundamental choices are Helicopter
and Fixed-wing, and each basic group contains
several model templates.
You must select one of the eight templates for
each new model. The template determines which
basic settings are adopted for the model.
The advantage of using model templates to set up
a new model is that many basic settings are al-
ready carried out for you; all you have to do is fine-
tune the values. For a detailed description of the
model templates please see Chapter (
c. Servo conf.
For each make of receiver, the servo configuration
defines the sequence in which the servos must be
connected to the receiver. If you are using MULTI-
PLEX equipment, Throttle is servo 4 , Rudder is
servo 3 , and so on. If you have already flown the
model using a different make of transmitter, the
assignment process will be quicker if you select
the appropriate configuration. In menu K, As-
signment , you can change the sequence in any
way you like.
You can choose from any of the following configu-
rations ( 21.3.):
M-PCM Sequence for M-PCM receivers
MPX-UNI Sequence as MULTIPLEX
Futaba Sequence as robbe / Futaba
JR Sequence as Graupner / JR
The signal format is always Universal (servo centre
= 1.5 ms).
d. Mode 1 to 4 , variable
The double arrows indicate which sticks are used
to control elevator ( è ) and rudder ( é ).
Mode determines the assignment of the primary sticks.
In our example the right-hand stick operates rudder
( é ) and elevator ( è ). This setting can be changed
at any time. Please refer to Chapters (
and ( 13.2.5.).
e. Assignment
You must select one of the five assignment lists
when you set up a new model (
Manual
19.3.).
21.).
12.2.5.)
22.1.).
87