Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ELECTRONIC
CONTROLS
SET-UP iNSTRUCTiONS
H.00
EXTRA RINSEUpgradePrice- Increase or decreasebetween0
EXTRA
and200by pressingthe LEFTUPPERor RIGHT UPPERkeypad.
RINSE
Factorypresetfor 1 coins= $0.25.
-> Pressthe LEFTMIDDLE keypad onceto advanceto nextcode.
J.Cd
COIN/DEBIT OPTION
J.Cd
Bothcoin &debit selected.
J.C
Coinsselected,debitdisabled.Pressthe LEFTLOWERkeypad
3 timesfor thisselection.
J.d
DebitCardselected,coinsdisabled.Pressthe LEFTLOWERkey
pad3 times forthis selection.
J.Ed
Enhanced Debitis self-selected when a Generation 2 card reader
is installedinthe washer.TheEd optioncannot be manually
selectedor deselected.
If cycle counter
(9.0C) is selected,
the following
is true:
1 xx Number of cycles in THOUSANDS.
1 02 = 2,000
2xxx Number of cycles in ONES.
2225 =
225
TOTAL CYCLES = 2,225
This is "VIEW ONLY" and cannot be cleared.
Press the LOWER MIDDLE key pad once to advance
to next code.
If money counter (1.00 or 1.00) is selected,
the following
is
true:
3 xx Number in THOUSANDS.
3 01 = $1,000.00
4xxx Number in ONES.
4600 = $
600.00
5 xx Number of HUNDRETHS.
5 75 = $
00.75
TOTAL = $1,600.75
EXIT FROM SET-UP MODE
[]
PD Models: Reinstall access door.
END OF SET-UP PROCEDURES
-->Pressthe LEFTMIDDLE keypad onceto advanceto nextcode.
L.O0
PRICESUPPRESSION OPTION
Thisoption causesthe customerdisplayto show 'ADD'or
'AVAILABLE' ratherthanthe amountof moneyto add.(Used
mainlyindebit installations.)
L.00
NotSelected'OFF'.
Table 1
L.PS
Selected'ON'. Pressthe LEFTLOWER key padonceforthis
selection.
.e Pressthe LEFTMIDDLE keypad onceto advanceto nextcode.
n. CE
CLEARESCROW OPTION
Whenselected,moneyheldin escrowfor 30 minuteswithout
furtherescrowor cycleactivitywill be cleared.
n. CE
Selected'ON'.
n. 00
Notselected'OFF'.Pressthe LEFTLOWERkeypadonceto
deselectthisselection.
.e Pressthe LEFTMIDDLE keypad onceto advanceto nextcode.
U.O0
COiN(HUNDREDTH) I NCREMENT OFFSET
U.00
For usewithcard readerapplicationsonly.
-> Pressthe LEFTMIDDLE keypad onceto advanceto nextcode.
A3.02
NORMAL Cycle Settings.Allowsthe ownerto selectthe cycle
defaultoptionsof WaterTemperature, SoilLevel,and ExtraRinse.
SeeTable1for specificsettings.Normalisset to 02 fromthe
factory.
A4.00
DELICATES CycleSettings.Allowsthe ownerto selectthe cycle
defaultoptionsof WaterTemperature, SoilLevel,and ExtraRinse.
SeeTable1for specificsettings.Delicatesis setto 00 from the
factory.
A5.OF
POWERWASH C ycleSettings.Allowsthe ownerto selectthe
cycledefaultoptionsof WaterTemperature, S oilLevel,andExtra
Rinse.
SeeTable1for specificsettings.Powerwashis setto OFfromthe
factory.
If preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
A3, A4,
Extra
Soil
Wash
A3, A4,
Extra
Soil
Wash
or A5
Rinse
Level
Temp
or A5
Rinse
Level
Temp
CO
Off
Off
Cold
08
On
Off
Cold
O1
Off
Off
Cool
09
On
Off
Cool
02
Off
Off
Warm
CA
On
Off
Warm
03
Off
Off
Hot
Ob
On
Off
Hot
04
Off
On
Cold
Oc
On
On
Cold
05
Off
On
Cool
Od
On
On
Cool
06
Off
On
Warm
OE
On
On
Warm
07
Off
On
Hot
OF
On
On
Hot
Technician Service Access Code
This method is only available on washers set to free vend (6 00).
To enter service
mode:
Press the LEFT UPPER, RIGHT LOWER, RIGHT UPPER, and
LEFT LOWER key pads within 10 seconds.
To exit service
mode:
From service code 8.xx, press the LEFT UPPER key pad
for 4 seconds
or
Wait 2 minutes without touching any key pads (without diagnostic
modes running)
or
Power down the washer, then reapply power
NOTE: If a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
19
Tabla de contenido
