TESY GH 200 Instrucciones De Uso Y Mantenimiento página 6

Manual mode:
EN
Press .
•
start at 1800W (screen display
operation could be conducted
Temperature setting
1.
•
Press SET once, the screen will flash 20°C (default
temperature is 20°C)
•
Use + or – to set temperature (5-40°C) and then
press OK to confirm setting
•
Heater will stop heating when ambient temperature
reaches the set temperature. When ambient
temperature is 2°C lower than the set temperature,
heater will restart heating.
When temperature setting finish: the screen will
automatically display the setting temperature in
working mode (SET icon and the setting temperature
will light up). Press OK to read room temperature. It will
automatically switch back to setting temperature in 5
seconds. The screen will display room temperature in
standby mode or towel heating mode. (SET icon will not
light up when room temperature is displayed only)
Mode Switch
2.
Press once to switch mode among 1800W ( ), 900W
( ) and cooling fan ( ) in cycle. The relevant icon will
light up during mode switch.
Towel Heating Function
•
Connect to supply power, press
towel heating function, to press it
it off. During towel heating mode, icon
all the time. Towel heating working power is 200W.
•
Towel heating function works individually. It could
be conducted when the appliance is in standby
mode. Working period is 2 hours each time. It will
automatically switch off in 2 hours when nobody
switches it off manually.
Note: The temperature SET should be higher than
the room temperature (the temperature icon on the
left). Otherwise, the appliance will not start heating.
Program mode:
In standby mode, long press
until program setting finishes:
6
Usage and Storage Instructions
), the following
once to switch on
again to switch
lights up
for 3 seconds, flashes
Set Wake Up Time and Temperature:
Screen 1 2 3 4 5 6 7 full displays, which mean you are
setting wake up time for the whole week, use + and – to
set current day, the selected day will flash, press ok to
confirm. Then hour icon
1
display (one box stands for one hour, totally 24 boxes for
24 hours). Use + and – and/or SET button to set hour,
the selected box will flash. You may set the start hour or
a working time range.
For example:
Set the heater to start at 8:00 a.m., use + and – to
1.
select the 8th box, it will flash, press OK to confirm it.
Set the heater to start work at 8:00 am and stop at
2.
10:00 a.m., firstly use + and – to select the 8th box,
then press SET, use + and – to select the 9th box,
these 2 boxes will flash, press OK to confirm it.
Then the SET temperature 20°C (default temperature
is 20°C) flashes. Use + and – to set target wake up
temperature (5-40°C).
Then press OK to move on to the next day wake up time
and temperature setting in the same way.
In the end, press OK to confirm and end the setting. All
icons will stop flashing.
(During the setting, you can press SET to activate/shut
down the wake up program for week-days.)
Note:
when week timer is set, icon
1.
time. If you don't need week timer, press
switch it off, the icon on screen will disappear at the
same time.
In week timer program, press
2.
the current day program mode. It will works
automatically in next day as pre-set program.
Body Detector (Motion Sensor)
Body detector only works when wake up time and
temperature are set. It starts to scan the surroundings
when the preset wake-up time comes and heater starts
heating.
When nobody is detected, heater will stop heating
1.
in 15 mins.
When somebody is detected, heater will keep
2.
heating until the room is detected to be empty. It
will stop heating 15 mins later after that.
When somebody is detected again, heater will
3.
recover to work again.
will full
6 12 18 24
will display all the
once to
to switch off