Nice Moon MC824H Instrucciones Y Advertencias Para La Instalación Y El Uso página 74

Before using the automation for the first time, ask the installer to explain
the origin of residual risks and devote a few minutes to reading this user
instruction and warning manual given to you by the installer. Keep the
manual for reference when in doubt and pass it on to new owners of the
automation.
IMPORTANT! – Your automation is a machine that performs your
commands faithfully; negligent or improper use may constitute a
hazard.
– Never activate automation controls if persons, animals or objects
are present in the operating range.
– NEVER touch parts of the automation while the gate or door is moving!
– Photocells are not safety devices but safety aids. They are con-
structed with very reliable technology but in extreme situations they
may malfunction or even break. In some cases this malfunction may
not be immediately evident. For this reason, observe the following
warnings when using the automation:
- Pass through the gate or door only when it is completely open and
the leafs have stopped moving.
- NEVER pass through while the gate or door is closing!
- Periodically check correct operation of the photocells.
• Children: an automation system guarantees a high level of safety, using
a special detection system to prevent movement in the presence of per-
sons or objects. Nonetheless, it is advisable to ensure that children do not
play in the vicinity of the automation. To prevent the risk of accidental acti-
vation, do not leave the remote controls within the reach of children It is
not a game!
• The product should not be used by children or people with impaired
physical, sensorial or mental capacities or who have not received ade-
quate training in the safe use of the product.
• Malfunctions: if the automation is seen to perform abnormally, discon-
nect the electrical power supply from the system and manually release the
gearmotor (see instruction manual) to operate the gate manually. Never
attempt to perform repairs; contact your local installer for assistance.
• Never modify the system or the control unit programming and
adjustment parameters: this is the responsibility of the installer.
• Power supply failure or absence: while waiting for the installer or the
electrical power supply to return, the automation can still be used even if the
system is not equipped with a buffer battery: manually release the gearmotor
(see instruction manual) and move the gate leaf manually as required.
• Safety devices disabled: the automation can be operated even when
a safety device does not work correctly or is out of use. The gate can be
controlled in the "hold-to-run" mode. Proceed as follows:
01. Send a command to operate the gate using a transmitter or a key
selector, etc. If everything operates correctly, the gate will move nor-
mally, otherwise proceed as follows;
02. Within 3 seconds, activate the control again and keep it activated;
03. After approximately 2 seconds, the gate will perform the required
movement in "hold-to-run"; mode; i.e. the gate will continue to move
only as long as the control is activated.
IMPORTANT! – If the safety devices are out of use, it is advisable to
have them repaired as quickly as possible by a qualified technician.
• Testing, periodic maintenance and any repairs must be documented by
the person performing the operations and the relevant documents must be
kept by the system owner. The only operations that can be performed by
the user are to clean the photocell lenses (use a soft and slightly damp
cloth) and remove any leaves or stones that may obstruct the automation.
Important – To prevent the door from being activated accidentally, before
proceeding release the automation manually (as described in the relevant
manual).
• Maintenance: Regular maintenance (at least every 6 months) is need-
ed to keep the level of safety constant and to ensure the maximum dura-
bility of the entire automation. Checks, maintenance and repairs must
be performed exclusively by qualified personnel.
II – English
Instructions and warnings for the user
• Disposal: At the end of the automation's lifetime, ensure that it is dis-
posed by qualified personnel and that the materials are recycled or
scrapped according to current local standards.
• If the automation has been blocked by a "Block automation"
command: after sending a command, the gate does not move and the
flashing light emits 9 short flashes.