Taurus SENSITY COMPACT NS Manual Del Usuario página 11

off until the steamer is ready , once this
happens the indicator will remain constant,
indicating that it is fully ready to iron. This
process takes about 60" and is controlled by the
product's electronics.
• Do not use temperatures higher than those
indicated on the garments to be treated.
● Temperature for synthetic fibres (Polyester,
Nylon...). (don't use this position to produce
steam)
●● Temperature for silk, wool. (Minimum tempe-
rature for ironing with steam)
●●● Temperature for cotton.
Max Temperature for linen.
• If garment has various kinds of fibres, select the
temperature for the fibre that requires the lowest
temperature. (For example, select the tempera-
ture for polyester for an article made out of 60%
polyester and 40% cotton).
• Wait until the pilot light (B) has gone out which
will indicate that the appliance has reached an
adequate temperature.
• Press and hold the steam button (C) for 10
seconds
• During use the pilot light (B) will automatically
flash on and off, thus indicating that the heating
elements are operating in order to maintain the
desired temperature.
DRY IRONING:
• The appliance has a steam and temperature
control (E) which when set to the MIN position
allows dry ironing (no steam).
STEAM IRONING:
• It is possible to iron with steam whenever the
deposit is filled with water and the adequate
temperature is selected.
STEAM FLOW CONTROL:
• The appliance allows the temperature and
steam flow (E) to be regulated, to adjust the
steam use a higher or lower temperature and
the appliance's electronics will adjust the steam
accordingly
• If the light (O) is switched, the water tank is
without water.
VERTICAL STEAMING
It is possible to iron hanging curtains, items of
clothing on his hanger, etc. To do so, follow the
instructions:
Select the maximum temperature of the iron,
while turning the temperature regulator of the
iron in a clockwise direction.
• Move the iron in a top to bottom direction while
pressing the steam control ( C ). Important: for
cotton and linen, its recommended to put the
iron base in contact with the material. For other
more delicated fibres, it's recommended to keep
the iron base at some centimetres of distance.
ANTI-SCALE WARNING:
• ANTI-SCALE FILTER: To ensure correct ope-
ration, replace the anti-scale filter after every 6
months of continued use.
into its housing. Use demineralised water to
continue using an already depleted cartridge.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
• Select the minimum position (MIN) using the
steam and temperature control.
• Unplug the appliance to the mains.
• Remove the water from the water tank.
• Clean the appliance
CLEANING
• Disconnect the appliance from the mains and let
it cool before undertaking any cleaning task.
• Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
• Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
• Do not submerge the appliance in water or any
other liquid, or place it under a running tap.
• Quick cleaning guide:
1) Fill the tank with approximately 1 litre of water.
(Do not put vinegar or other descaling agents
into the water tank)
2) Plug in the ironing system and set the tempera-
ture control to MIN.
3) Hold the iron vertically over the sink and press
the steam button (C) for 1 minute to pump the
water from the tank to the iron.
4) Increase the iron's temperature setting to
number 2
5) Place the iron horizontally over the sink, keep
pressing the steam button (C) and gently rock
the iron backwards and forwards for 1 minute.
6) Unplug the ironing system from the mains
supply and immediately rub the soleplate with a
damp cotton cloth folded several times. (Never
Fit the new cartridge