Sammic TR Instrucciones De Uso página 4

CE Marking Indications
Each appliance is identified by the following
data:
· Manufacturer's name and address: SAMMIC
S.L. C/ Basarte 1 - 20720 Azkoitia Gipuzkoa
(SPAIN).
· "CE" mark.
· The machine model as stated in the next
section.
· The serial number as indicated on the
guarantee slip and the Declaration of
Conformity.
MODELS
This manual describes the
operation and maintenance of the TR-220, TR-
270, TR-350, TR-550, TR-750, TR/BM-270 and
TR/BM-350 portable electric appliances.
The model reference and its specifications are
shown on the nameplate affixed to the machine.
These appliances have been designed and
manufactured in accordance with the following
standards:
European Directives and Standards (Version
fed at 230V, 50/60Hz)
- Low Voltage Directive: 73/23/EEC
- Machine Directive: 89/392/EEC
- Electromagnetic Compatibility
89/336/EEC
- Amendment to directives: 93/68/EEC
- Standards for machine safety: UNE-EN
60335-2-64 and 60335-1
- Interference Emission Norms:
55014, 61000-3-2 and 61000-3-3
- Interference Immunity Norms UNE-EN 55014-
2
- Degree of protection IP 24 according to norm
IEC 60529 Standard.
Applicable American Standards (Version fed
at 115V, 60Hz)
- Standards for Machine Safety: UL 1097, UL
763, UL 94
- Standards for Hygiene and Food Equipment
Materials: ANSI-NSF 8 and ANSI-NSF 51
INSTALLATION AND OPERATION
Before using the machine for the first time,
clean the area in contact with food with
(lukewarm) soapy water, rinse and leave to dry.
For optimum performance and long service life
4
EN
of the machine, follow the installation and start-
up instructions contained in this manual
rigorously as well as the recommended
conditions of use.
Installation
Before plugging the appliance, check for a
match between the mains voltage and the
appliance voltage
nameplate.
There is a wall mount supplied with the
appliance. Determine an appropriate location
for this support.
Directions for Use
installation,
Plug the appliance into an outlet.
Introduce the foot into the bowl, up to a
maximum of 2/3 the foot's length. For optimum
operation, it is better if the foot does not touch
the bottom of the bowl. In order to prevent
splashed food from getting inside the motor
unit, it is recommended not to incline the
appliance more than 30º (See Figure 6).
Once finished working, unplug the appliance if it
is not going to be used again.
In the event of overheating due to prolonged
use or overload, the thermal switch would
protect the motor, stopping it. If this occurs,
allow the blender to cool before restarting it.
Directive:
Function of the controls
Models TR-220 and TR-270 (See Figure 3)
ON/OFF switch (6): Pressing this button
UNE-EN together with the Safety one (7) will cause the
appliance to operate.
Safety (7): If this button is not actuated, the
appliance will not start. Once in operation, the
appliance will not stop when this push-button is
released.
Variator control (12, model TR/BM-270 only):
serves to change the speed of the blade or
stirrer.
Models TR-350, 550 and 750 (See Figures 4
and 5)
ON/OFF switch (9): Pressing this button
together with the Safety one (11) will cause the
appliance to operate. Unless locked, the
appliance will stop as soon as this push-button
is released.
Safety (11): If this button is not actuated, the
appliance will not start. Once in operation, the
appliance will not stop when this push-button is
released.
Lock (10): This button is intended to lock the
appliance in the operating condition, so that it
operates even when all push-buttons are
released. Unlocking the appliance is achieved
by pressing the 'Start' button again (9).
Variator control (8, model TR/BM-350 only):
serves to change the speed of the blade or
stirrer.
as specified on the F
ITTING OF THE BLENDER
TR-350, TR-550 and TR-750)
Insert the coupling shaft of the blender (2) into
the motor unit (1) and turn the foot
counterclockwise until it is securely clamped.
F
ITTING OF THE BEATER
TR/BM-350)
Insert the coupling shaft of the beater (3) into
the motor unit (1) and turn the foot
counterclockwise until it is securely clamped.
F
ITTING
TR/BM-270 and TR/BM-350)
Fitting: introduce the end of the stirrer into the
hole in the gear attachment, turning and
pushing the same to a stop.
Removing: Pull firmly from the stirrer until it
comes off the gear attachment.
MAINTENANCE
- If the power cord gets damaged and must be
replaced, such a change may only be done by
a SAMMIC-approved technical assistance
service.
- The blades wear in time and have to be
replaced periodically.
- Check regularly the foot and gear attachment
for tightness.
Cleaning and hygiene
W
ARNINGS
- To prevent electric shock that can cause
serious personal injury, always unplug the
blender before cleaning. Once cleaned,
connect it again.
- In order to avoid damage to people and the
appliance, read and follow the manufacturer's
instructions for the cleaning of the blender.
- Do not use the following products:
- Abrasive cleaners, such as ammonia, lye,
- Solvents
- Metal scourers
- Gritty detergents.
These products would score, scratch and
(models TR/BM-270,
(models TR/BM-270 and
/
REMOVING OF THE STIRRER
etc.
(models