Philips 26PF5321 D/37 Guía De Uso Rápido página 11

CABLE
7g£_
0 Basic connections to the TY
Your integrated digital TV automatically decodes and displays the four basic DTV
picture resolution standards.
- SDTV (Standard Definition TV) are broadcast as 480i (480-line interlaced) or
480p (480dine progressive scan) video.
- HDTV (High-Definition TV) are broadcast either in the 1080i or 720p formats,
always with a widescreen picture.
Note: Progressive scan video (p) is more like that you see in a movie theaten Images are
much morn distinct and free of flicker, and motion is smoothen
Next to analog NTSC broadcast reception, your TV has an integrated High
Definition TV tuner which receives, decodes and displays terrestrial ATSC and
unscrambled cable (QAM) signals.
HDTV quality is only reproduced when a broadcaster or cable provider broadcasts
HDTV signals.
BLE 7sn
OU'T T J
®i
Set-Top Box
AVl:
L÷I÷VlOEO
®
®
Set-Top Box
There are 2 ways to get HDTV content:
- via cable,
- via antenna.
Note; This dry;wing is used wherever you can connect cable or antenna,
- Cable TV
Connect the cable TV signal to the CABLE/ANTENNA 75 I_F" jack at the bottom
of the TV. See page 8 for details on using Autoprogram to store channels in the
TV's memory.
Note: this connection will supply stereo sound to the TV if it is being broadcast by the
station you am watching,
- Cable box with IF IN/OUT
• Connect the incoming cable TV signal to the cable IN jack C) on the back of
the cable box.
• Connect a coaxial cable (not supplied) from the TO TV jack on the back of the
cable box to the CABLE/ANTENNA 75 n'll" jack (_ at the bottom of the TV.
Note: Your cable box may have a different label for the TO TV jack, such as
OUTPUT or OUT
" Set the OUTPUT CH switch (_) of the cable box to ¢H 3 or 4 (whichever is
correct for your cable box), then tune the TV to the corresponding channel
Once tuned, change channels at the cable box, not the TV.
Note: This connection will not supply stereo sound to the TK The reason is that the RF
output on a cable box - labeled TO TV, OUT or OUTPUT _br example will not send a
stereo signal to the tuner (VHF/UHF) input on a TK
- Cable box with AIV outputs
• Connect the incoming cable TV signal (_ to a signal splitter (not supplied).
The signal splitter enables you to avoid having to use the TO TV jack on the
back of the cable box. This jack will not supply stereo sound to the TV,
Note: Your cable box may have a clifferent label for the TO TV jack, such as
OUTPUT or OUT
• Connect a coaxial cable (not supplied) to a connector on the signal splitter and
to the CABLE/ANTENNA 75 n=l_ jack (_) on the TV.
. Connect another coaxial cable (not supplied) to a connector on the signal
splitter and to the cable IN jack (_) on the back of the cable box.
. Connect A/V cables (not supplied) to the VIDEO and AUDIO L and R outputs
on the back of the cable box and to the AV2 video (labeled VIDEO) and
AUDIO (labeled L and R) jacks (_) on the back of the TV.
. To view programs from your cable box, first press the AV+ button on the
remote control.
• Press the cursor clown or up buttons until the AV2 signal source is selected.
. Press the OK button to confirm your selection. The AV2 input source
becomes current for the viewing of cable TV programs through your cable box.
Note; If your cable box Audio/Video outputs will not supply wdeo and stereo au@o to
the T_, you will need to make the connection shown above in the example "Cable box
with RF INIOUT",