BFT CLONIX 2E AC U-LINK 230 Manual De Instalación página 16

TABLE "A" – RADIO MENU (RADIO)
Logic Description
Add Key to output OUT 1
OUT 1 add
associate the required key to the OUT 1 output
Add Key to output OUT 2
OUT 2 Add
associate the required key to the OUT 2 output
Add Key to output OUT 3
OUT 3 Add*
associate the required key to the OUT 3 output
Automatically associates T1 to OUT 1, T2 to OUT 2, T3 to OUT 3 (where present).
aut.
Erase List
WARNING! Erases all memorized transmitters from the receiver's memory.
erase 2048
Read receiver code
cod RX
Displays receiver code required for cloning transmitters.
* only on CLONIX UNI AC U-LINK 230.
TABLE "B" - OUTPUT CONFIGURATION MENU (outputs)
OUTPUT Definition
Out 1 output
configuration.
out1
20-21
Out 2 output
configuration.
out2
22-23
Out 3 output
configuration.
out3*
24-25
* only on CLONIX UNI AC U-LINK 230.
Table B1
Parameter value Time interval
1
2
3
4
5
6
7
8
9
16 -
CLONIX U-LINK
INSTALLATION MANUAL
Default Cross out setting used
monos
bist
timed
monos
antipanic
monos
bist
timed
monos
antipanic
monos
bist
timed
monos
antipanic
30s
60s
2 minutes
5 minutes
15 minutes
30 minutes
1 hour
2 hours
12 hours
Pulse or non-latching type output, the associated output relay is attracted for 1 second.
Jog type output (latching), the associated relays switches status each time the transmitter
key is pressed.
Each time the transmitter key is pressed the output
relay remains attracted for an interval of time that can
be set according to the following table. Pressing the
key during the count cycle resets the count.
The associated output relay switches status if the transmitter key is held down for more than 5
seconds. All transmitter keys on the receiver are automatically equipped with the anti-aggression
function regardless of their configuration, thus the output need not be assigned a key (T1,T2,T3
or T4) Relay switching lasts 10s.
If linked to a transmitter key and held down for less than 5 sec., it behaves like a non-latching output.
Only one output can be configured with anti-aggression mode.
Pulse or non-latching type output, the associated output relay is attracted for 1 second.
Jog type output (latching), the associated relays switches status each time the transmitter
key is pressed.
Each time the transmitter key is pressed the output
relay remains attracted for an interval of time that can
be set according to the following table. Pressing the
key during the count cycle resets the count.
The associated output relay switches status if the transmitter key is held down for more than 5
seconds. All transmitter keys on the receiver are automatically equipped with the anti-aggression
function regardless of their configuration, thus the output need not be assigned a key (T1,T2,T3
or T4) Relay switching lasts 10s.
If linked to a transmitter key and held down for less than 5 sec., it behaves like a non-latching output.
Only one output can be configured with anti-aggression mode.
Pulse or non-latching type output, the associated output relay is attracted for 1 second.
Jog type output (latching), the associated relays switches status each time the transmitter
key is pressed.
Each time the transmitter key is pressed the output
relay remains attracted for an interval of time that can
be set according to the following table. Pressing the
key during the count cycle resets the count.
The associated output relay switches status if the transmitter key is held down for more than 5
seconds. All transmitter keys on the receiver are automatically equipped with the anti-aggression
function regardless of their configuration, thus the output need not be assigned a key (T1,T2,T3
or T4) Relay switching lasts 10s.
If linked to a transmitter key and held down for less than 5 sec., it behaves like a non-latching output.
Only one output can be configured with anti-aggression mode.
Description
See table B1
See table B1
See table B1