Tabla de contenido
Idiomas disponibles
Idiomas disponibles
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please used
an approved extension cable that fits the tool's power input
specifications. The minimum cross-sectional area of the
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Cable cross-sectional
area (mm
) Cable rated
2
current (Ampere)
0,75
1,00
1,50
2,50
4,00
Voltage
Amperes Cable rated current (Ampere)
110-127
0 - 2,0
2,1 - 3,4
3,5 - 5,0
5,1 - 7,0
7,1 - 12,0
12,1 - 20,0
220-240
0 - 2,0
2,1 - 3,4
3,5 - 5,0
5,1 - 7,0
7,1 - 12,0
12,1 - 20,0
FEATURES (FIG. A)
This tool includes some or all of the following features.
1. ON/OFF Switch
2. Spindle Lock
3. Guard
ASSEMBLY
WARNING! To prevent accidental operation, turn off and
unplug tool before performing the following operations.
Failure to do this could result in serious personal injury.
Attaching and Removing the Wheel Guard (Fig. B)
WARNING! To minimize the danger of serious personal
injury, please switch off the tool power and disconnect all
plugs before adjusting or removing/installing any accessory.
Cable cross-sectional
area (mm
) Cable rated
2
current (Ampere)
6
10
15
20
25
Cable length (m)
7,5
15
25
30
45
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
Before reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
Attaching the Guard
1. Place the angle grinder on a work bench, groove
facing up.
2. Bring the flange of the guard (3) collar over the groove
(9) of the gear housing.
3. Turn the guard (3) counterclockwise by 150 degrees.
4. Make sure that the screws (10) are tightened.
Removing the Guard
1. Loosen the screws (10) on the guard collar.
2. Pull up the guard (3).
WARNING! Do not operate the tool when the safety guard
is not in place.
Note: Refer to the grinding accessories chart at the end of
this section for accessories that can be used together with
this angle grinder.
Attaching and Removing Grinding Wheels
60
(Fig. C and D)
WARNING! Do not use damaged grinding wheels.
10
1. Place the tool on a work bench, groove facing up.
2. Figure C: Attach the inner flange (4) correctly on the
15
output shaft (5).
20
3. Place the grinding wheel (6) on the inner flange
(4).When attaching a grinding wheel with a raised
25
center,make sure that the raised center (7) faces the
-
innerflange (4).
-
4. Figure D: Tighten the outer flange (h) until the output
shaft (5).
6
4). When attaching the grinding wheel, the ring on top
6
ofthe outer flange (8) must face the wheel.
5. Press the spindle lock (2) and prevent the spindle (4)
15
from rotating until it locks in place.
15
6. Use the pin spanner to tighten the outer flange (8).
20
Preparation Before Use
-
♦ Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
♦ Make sure that the inner and outer flanges are attached
correctly.
♦ Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the accessories
and tool.
OPERATION
WARNING! Always observe the safety instructions
and applicable regulations.
WARNING! To minimize the danger of serious personal
injury, please switch off the tool power and disconnect all
plugs before adjusting or removing/installing any accessory.
Before reassembling the tool, press and release the trigger
switch to make sure the tool is already switched off.
ENGLISH (
Original Instructions)
23
Tabla de contenido
