Configuration - Vimar ELVOX ZR01 Manual Para El Conexionado Y El Uso

D. DIP SWITCHES
After each dip switch change the sensor launches a learning process
Dip-switch #1 Frequency Adjustments of Loop A
Dip-switch #2 Frequency Adjustments of Loop A (with single loop) or Loop B (with dual loops)
Dip-switch #3 Relay configuration : active or passive.
Dip-switch #4 Automatic Sensitivity Boost (ASB option) [recommended for better trucks detection] :
During a detection the sensitivity increases automatically to 8 times the preset sensitivity given by the sensitivity potentiometer adjustment.
It is limited to the maximum sensitivity (Äf = 0.005%).
It goes back to the preset value after detection stops.
Dip-switch #5 Relay A function : presence or pulse (not used with dual loop in combined mode)
Dip-switch #6 Relay A Pulse type : entry or exit (used only at pulse function)
or Relay B mode (with dual loop in combined mode) (see next drawing)
• non-directional :
The relay B provides a pulse according to the dip switches #7 and #8 setting.
• directional A
The relay B provides a pulse only if the loop A is detecting before the Loop B.
The detection takes place according to dip switches #7 and #8 logic.
Warning : During the detection, the 2 loops have to detect simultaneously for a short period to be able to determine the movement direction.
During loop installation make sure the 2 loops are close enough to each other to ensure a common detection (typical 1m).
Dip-switch #7 Relay B function : presence or pulse or loop selection for relay B pulse : pulse on Loop B or pulse on Loop A (used with dual loop in
combined mode)
Dip-switch #8 Relay B Pulse type : entry or exit (used only at pulse function)
Dip-switch #9 Pulse duration for both relays (used only at pulse function): 100 ms or 500 ms
Dip-switch #10 Dual loop mode : independent or combined A— B (not used with single loop)

Configuration #1

Single loop
OFF
DS#1
See next table
DS#2
DS#3 Active mode
DS#4 ASB OFF
DS#5 Relay A :
Presence on loop A
DS#6
Relay A :
Pulse on loop A
entry
DS#7 Relay B :
Presence on loop A
DS#8 Relay B :
Pulse on loop A
entry
DS#9
100 ms
DS#10 not used
EN
B :
Dual loop in independent mode
ON
High (loop A)
High (loop B)
Passive mode Active mode
ASB ON ASB OFF
Relay A : Relay A :
Pulse on loop A Presence on loop A
Relay A : Relay A :
Pulse on loop A Pulse on loop A
exit entry
Relay B : Relay B :
Pulse on loop A Presence on loop B
Relay B : Relay B :
Pulse on loop A Pulse on loop B
exit entry
500 ms 100 ms
not used Independent mode
Configuration #2
OFF ON
Low (loop A)
[High –30%]
Low (loop B)
[High –30%]
Passive mode
ASB ON
Relay A :
Pulse on loop A
Relay A :
Pulse on loop A
exit
Relay B :
Pulse on loop B
Relay B :
Pulse on loop B
exit
500 ms
Combined mode
Configuration #3
Dual loop in combined mode
ON
High (loop A) Low (loop A)
[High –30%]
High (loop B) Low (loop B)
[High –30%]
Active mode Passive mode
ASB OFF ASB ON
not used not used
Relay B : Relay B : directional
non-directional A— B mode
mode
Relè B : Relè B :
Impulso sulla spira B Impulso sulla spira A
Relay B : Relay B :
Pulse on loop Pulse on loop
entry exit
100 ms 500 ms
Independent mode Combined mode
ON
5