KBS PRISMA 200 TBS-PF Manual Del Usuario página 8

7. CONNECTION TO THE MAINS
1.
Ensure that mains voltage and frequency are the same as those stated on the rating plate (A) attached
2.
to the appliance. Ensure that the supply socket has the following characteristics:
b)
earthed. It fulfils the requirements of the rated current as set out on the rating plate.
the IEC regulations: - magnetothermal differential switch (also known as ground fault interrupter) with In
= nominal value as stated on the rating plate; - Differential with Id sensitivity = 30 mA. . Ensure that
there is no danger of explosion (AD) in the room. . The connecting cable to the appliance is H05 VVF,
designed for internal use. For installation in any other environments, it will be necessary to change the
cable with the appropriate type (for example H07 VVF for external use).
three-way adapters and reduction adapters).
placed by mistake in a horizontal position or has been turned upside down, leave for at least three hours
in the correct position before switching on the power supply (see figure 4).
8. CONTROLS
The appliance features adjusting controls, located at the front of the cabinet.
TB/PF models: 1. Light switch:
switch:
to switch on the refrigeration system.
Thermostat:
appliance. to adjust the temperature in the appliance.
display the temperature set-point, which can be changed by pressing button
"DOWN" PRISMA 400 TNV/PG model: 1. Rotation switch:
.
Light switch:
to switch on the light inside the display cabinet.
refrigeration system (see figure 6).
9. CHECKING CORRECT OPERATION
Check that: 1.
The plug is connected. . The refrigeration unit switch is switched on (green light on).
3
. The thermometer shows the desired temperature for the goods to be stored. . The appliance is not
exposed to direct sunlight or to high-powered lamps. . The room temperature does not exceed that in
which the appliance is designed to work normally, i.e. + 25°C, 60% r.h. (climatic class 3).
appliance must be correctly filled, without overloading the shelves and with sufficient space for correct
cold air circulation.
10. INTERNAL CLEANING (EVERY 15 DAYS)
1.
Switch off the appliance.
accessories with a sponge dipped in water with a little sodium bicarbonate. Dry with care.
11. REPLACING THE INTERNAL LIGHTS
1.
Switch off the appliance. . Undo the screws which hold the top lamp socket in place. . Detach the
fluorescent tube with its protective cover from the top lamp socket. . Take the tube out of the bottom
5
lamp socket. . Remove the protective cover. . Replace the fluorescent tube. . Reassemble by following
the above instructions in reverse order (see figure 7).
12. REPLACING THE DOOR'S MAGNETIC GASKET
1. 2.
Open the door. Take hold of the magnetic gasket and pull it out of the frame.
gasket and press it firmly down all around (see figure 8).
Operator's guide
4
N.B.
If during transport or storage the appliance has been
to switch on the light inside the display cabinet.
3. Thermometer:
2
5
2
. Open the door and remove the refrigerated goods.
2
6
7
a)
it is properly
c)
3
5
. Connect the plug (do not use
PRISMA 200-
2. Refrigeration
to display the temperature in the
a) 5 "SET or P"
Press button
6 "UP"
or button
to set the rotating shelves into motion.
3. Refrigeration switch:
to switch on the
4
3.
Wipe the sides and
4
7
3
. Insert the new
It complies with
UK
D
NL
400TN/PF
once to
7
2.
DK
FIN
B
GR
N.B.:
the
CZ
EE
LV
LT
3
H
M
PL
SK
SLO
I
E
F
P
S