Memory Capacity - tau K206MA Guía Para La Instalación

10. RESTORING AUTOMATIC OPERATION
Should the Bar need to be operated manually, use the release system. After the manual operation:
• after a Mains Power Failure, such as a black-out (controller remains disconnected for a certain time),
the automation will be moving slowly to allow the Controller to establish its Limits (REALIGNMENT);
• after a Manual Operation without Mains Power Failure (controller remains connected) it will take 1
complete cycle to complete the realignment procedure. During this cycle, Limits and Soft-Stops will
not be working.
11. 433.92 MHz BUILT-IN RADIO RECEIVER
The radio receiver can learn up to a maximum of 86 rolling codes (BUG2R, BUG4R, K-SLIM-RP, T-4RP)
which can be set on the two channels as required.
The first channel directly commands the control board for opening the automatic device; the second
channel commands a relay for a N.O. no-voltage output contact (terminals 19 - 20, max. 24V AC, 1 A).
LEARNING SYSTEM FOR RADIO CONTROL DEVICES
CH1 = OPEN/CLOSE
CH2 = 2 channel
nd
1_ press button CH1 briefly to associate a radio control device with the OPEN/CLOSE function;
2_ the (green) DL8 LED is ON to indicate the code learning mode has been activated (if no code is
entered within 10 seconds the board exits the programming function);
3_ press the button of the relative radio control device;
4_ the (green) DL8 LED turns off to indicate saving is complete and then on again immediately wait-
ing for other radio control devices (if this is not the case, try to re-transmit or wait 10 seconds and
restart from point 1);
5_ to memorise codes to other radio control devices, press the key to be stored on other devices
within 2-3 sec. After this time (DL8 LED turns off) must repeat the procedure from point 1 (up to a
maximum of 86 transmitters);
6_ if you wish to save on the 2nd channel, repeat the procedure from point 1 using the CH2 key instead
of CH1 (in this case the DL8 LED is yellow);
7_ to exit the learning mode without memorising a code, press button CH1 or CH2 briefly.
If the maximum number of radio controls is reached (86), the LED DL8 will begin to flash
rapidly for about 3 seconds but without performing memorisation.
REMOTE PROGRAMMING BY MEANS OF T-4RP and K-SLIM-RP (V 4.X)
With the new version of software V 4.X it is possible to carry out the remote self-learning of the new version
of transmitters T-4RP and K-SLIM-RP (V 4.X), that is without pressing the receiver's programming buttons.
It will be sufficient to have an already programmed transmitter in the receiver in order to start the
procedure of remote programming of the new transmitters. Follow the procedure written on the in-
structions of the transmitter T-4RP and K-SLIM-RP (V 4.X).
CANCELLING CODES FROM RADIO CONTROL DEVICES
1_ keep button CH1 pressed for 3 seconds in order to cancel all the associated radio control devices;
2_ LED DL8 flashes slowly to indicate that the cancellation mode has been activated;
3_ press button CH1 again for 3 seconds;
4_ LED DL8 turns off for approx. 3 seconds and then remains steady to indicate that the code has been
cancelled;
5_ repeat the procedure from point 1 using button CH2 to cancel all the associated radio control devices;
6_ to exit the learning mode without memorising a code, press button CH1 or CH2 briefly.

MEMORY CAPACITY

The code memory capacity* of the K206MA can be expanded from 86 to 126, 254 or 1022 codes (transmit-
ters) by replacing the memory cards as follows (plug them onto J3 connector, see wiring diagram):
126 codes
254 codes
1022 codes
Art. 250SM126
Art. 250SM254
Art. 250SM1022
22