Svrs Tripping; Section 5. Service And Maintenance; Routine Maintenance; Winterizing The Pump - Jandy ePump Pro Serie Manual De Instalación Y Operación

Jandy Pro Series ePump
®
NOTE Do not use petroleum based lubricants or
sealants on the lid o-ring.
4. Hand-tighten the lid to make an air tight seal. Do
not use any tools to tighten the lid: hand-tighten
only. Make sure all valves are open and the unions
are tight.
5. Restore power to the pump. Then turn on the pump
by following the instructions in the appropriate
manual: ePump + SVRS Controller Owner's
manual, H0412200, AquaLink
Manual, 6593, AquaLink PDA Owner's Manual,
H0572300, or AquaLink Z4 Owner's Manual,
H0386600.
6. Once all the air has left the filter, close the
pressure release valve.
7. The pump should prime. The time it takes to prime
will depend on the elevation and length of pipe
used on the suction supply pipe. See Installation
Recommendations in Section 3 for proper
elevation and pipe size.
8. If the pump does not prime and all the instructions
to this point have been followed, check for a
suction leak. If there is no leak, repeat Steps 2
through 7.
9. For technical assistance, call Zodiac
Support at 800.822.7933.
4.2

SVRS Tripping

SVRS functionality of the variable speed pump detects
full-body entrapment events by electrically monitoring
the change of the load on the pump. If an entrapment
event is detected, the motor shuts down, eliminating
the vacuum created by the pump. Once an entrapment
is sensed the motor goes into the fault state and stays
there for 4 minutes. After 4 minutes, the fault is cleared
automatically, and the motor is ready to run again.

Section 5. Service and Maintenance

5.1

Routine Maintenance

Inspect the pump filter basket for debris by looking
through the clear pump lid. Remove any debris, because
as debris accumulates, it will begin to block the flow of
water through the pump. Keep the filter basket clean to
improve the performance of the pump.
1. Turn off the power to the pump. If the pump is
located below the water level, close the isolation
valves on the suction and discharge sides of the
pump to prevent backflow of water.
2. Turn the lid's locking ring counter-clockwise until
'START' aligns with the ports. Carefully remove
the lid. (You may use a tool for leverage.)
|
+ SVRS Installation and Operation Manual
™
RS Owner's
®
Technical
®
CAUTION
A misaligned filter basket will cause the lid to be
improperly seated, allowing an air leak, which could
result in pump damage.
3. Lift the filter basket out of the pump.
4. Dispose of the debris and thoroughly clean the
filter basket, making sure all the holes are open.
Using a garden hose, spray the filter basket from
the outside to help clear the holes. Remove any
remaining debris by hand.
5. Replace the filter basket in the pump by aligning
the opening with the suction pipe. If aligned
properly, the filter basket will drop easily into
place. Do not force it into place.
6. Remove the lid seal and remove debris around the
lid seal seat, as this can allow air to leak into the
system. Clean the lid seal and place it on the lid.
7. Replace the lid with locking ring. Hand-tighten
the lid to make an air-tight seal. Do not use any
tools to tighten the lid: hand-tighten only.
8. Verify that all valves have been returned to the
proper position for normal operation.
9. Open the pressure release valve on the filter, and
make sure it is clean and ready for operation.
10. Turn on the power to the pump. Once all the
air has been evacuated from the filter, close the
pressure release valve.
5.2

Winterizing the Pump

CAUTION
The pump must be protected when freezing
temperatures are expected. Allowing the pump
to freeze will cause severe damage and void the
warranty.
CAUTION
Do not use antifreeze solutions in the pool,
spa, or hot tub systems! Antifreeze is highly toxic
and may damage the circulation system. The only
exception to this is Propylene Glycol. For more
information, see your local pool/spa supply store or
contact a qualified swimming pool service company.
1. Drain all water from the pump, system equipment,
and piping.
2. Remove the two (2) drain plugs. Store the drain
plugs in a safe location and reinstall them when
the cold weather season is over. Do not lose
the o-rings.
ENGLISH
Page 17