Honeywell TL8100 Instrucciones De Instalación
Honeywell TL8100 Instrucciones De Instalación

Honeywell TL8100 Instrucciones De Instalación

Ocultar thumbs Ver también para TL8100:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

TL8100
7 DAY PROGRAMMABLE HYDRONIC THERMOSTAT
GUIDELINES
TURN OFF POWER TO THE HEATING SYSTEM AT
THE MAIN POWER PANEL TO AVOID ELECTRICAL
SHOCK. INSTALLATION SHOULD BE CARRIED OUT
BY AN ELECTRICIAN.
• For a new installation, choose a location about 5 ft.
(1.5 m) above the floor.
• The thermostat must be installed on an inside wall.
• Avoid locations where there are air drafts (top of
staircase, air outlet), dead air spots (behind a door),
direct sunlight, or concealed chimneys or stove pipes.
PROCEDURE
1. Loosen the captive screw securing the front mod-
ule to the rear module as shown in Fig. 1.
2. Lift the lower part of the front module to remove it
from the rear module.
3. Loosen the captive screw holding the terminal
cover and remove the cover.
4. Pass the wires through the opening to the right of
the terminals. See Fig. 2. Secure the rear module
to an electrical box or to the wall using the supplied
wall anchors and screws.
5. Connect the wires (see section "Thermostat Wir-
ing" on page 2). Use 12 AWG or smaller wire. 14
AWG is recommended for line voltage, 18 AWG is
recommended for 24 VAC.
6. Install the terminal cover and tighten the screw.
7. Configure the thermostat using the switches
located on the back of the front module (see sec-
tion "Thermostat Configuration" on page 3).
8. Install the batteries (see section "Power-up" on
page 3).
9. Mount the front module onto the rear module and
tighten the screw.
INSTALLATION INSTRUCTIONS
2
1
4
5
8
7
Fig. 1. Installation steps.
Fig. 2. Routing wires to thermostat.
3
6
9
M29963
SUPPLY
LOAD
PROVIDED
WIRES
M29964
Tabla de contenido
loading

Resumen de contenidos para Honeywell TL8100

  • Página 9: Termostato Programable

    TL8100 TERMOSTATO PROGRAMABLE INSTRUCCIONES DE INSTALACIÓN INSTRUCCIONES CORTAR LA ALIMENTACIÓN DEL SISTEMA DE CALEFACCIÓN EN EL PANEL CENTRAL PARA EVITAR RIESGOS DE ELECTROCUCIÓN. LA INSTALACIÓN DEBE REALIZARLA UN ELECTRICISTA. • En el caso de una instalación nueva, elegir un sitio a alrededor de 1.5 m (5 ft) sobre el piso.
  • Página 10: Cableado Del Termostato

    TL8100 CABLEADO DEL TERMOSTATO V8043F TH, TR TH TR TL8100 120 V CA o 240 V CA CARGA INDUCTIVA MÁXIMA DE 2 AMP M29978 TL8100 MS29965 Fig. 30. Diagrama de cableado de la V8043F de 24 V CA. Fig. 25. Diagrama de cableado de un circulador de voltaje de línea.
  • Página 11: Configuración Del Termostato

    TERMOSTATO ventilación y aire acondicionado, menor debe ser el diferencial. • Cuando se conectan más de un TL8100 directamente En la Table 7 se muestra la configuración de los a una válvula de zona o a un circulador de zona.
  • Página 12 TL8100 By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’...

Tabla de contenido